JD VIP Buyers Club
JD on Facebook
JamestownTV
JD Points Program
Request A Free Catalog

Teleflex Mechanical Steering Connection Kits Overview




Technical Reference Manual



Steering Connection Kits Overview:

There are four basic types of connections for mechanical steering.

•Tilt Tube Mount


This is the most popular steering cable-to-engine con nec tion method for outboards with an ABYC standard tilt tube. This installation requires the use of a link arm which can be pur chased from the engine manufacturer.
Parts Required: Engine Manufacturer's Link Arm

•Transom Support Mount


This cable connection is used for older model outboards without tilt tubes, low HP out boards or applications where transom design interferes with standard tilt tube mounting.
Parts Required: D, G & H Master Kits (Include D, G & H): Stainless Steel Transom Mount Kit SA27255P or Corrosion Resistant Transom Mount Kit SA27256P (See following pages for individual components.)

•Splashwell Mount


This cable connection is used on boats where standard tilt tube or transom support mount ing methods are precluded by a splashwell box or lack of engine tilt tube. The mount ing surface is usually near per pen dic u lar to the transom and between 12 and 16 inches from the center line of the boat and/or tiller (25-33" total splashwell width).
Parts Required: B, H (90°) or A, H (15°)
Master Kits (Include H & A/B):
90° Splashwell Mount Kit SA27254P or
15° Splashwell Mount Kit SA27253P
(See following pages for individual components.)

•Inboard Stringer Support Mount


This connection is used on inboards and is attached to a stringer or suitable mount ing bracket below deck. The cable is perpendicular to the centered tiller and in half stroke for proper operation. An additional bracket may be needed to support the ball post. Available in heavy duty "Ski Boat" versions, with either long (4.5") or short (2.25") post standoff.
Parts Required: E,G,H (long post) or F,G,H (short post)
(See following pages for individual components.)

Back to the Top

Connection Kits for Cable to Engine and Cable to Helm


Teleflex Steering Connection Kits:


NOTE: Parts shown on this page are available in kit form ONLY.
Index: A, B, C, D, E, F, G, H, I, J, M, N, O, P, Q, R

A


SPLASHWELL MOUNT KIT
15° Corrosion Resistant
SA27253P
(NOTE: OUTER RING NOT SOLD SEPARATELY)
(BOOT ONLY P/N: SA37868P)
Back to Index

B


SPLASHWELL MOUNT KIT
90° Corrosion Resistant
SA27254P
(NOTE: OUTER RING NOT SOLD SEPARATELY)
(BOOT ONLY P/N: SA37868P)
Back to Index

C


SPLASHWELL THREADED
TUBE WITH BALL

Corrosion Resistant
SA36316P
(NOTE: OUTER RING NOT SOLD SEPARATELY)
(BOOT ONLY P/N: SA37868P)
Back to Index

D


CLAMP BLOCK-OUTBOARD
Stainless Steel
SA27149P
Corrosion Resistant
SA27055P
Back to Index

E


CLAMP BLOCK-SKI BOAT IN BOARD
4-1/2" Stand-Off
SA27579P


(Heavy Duty with Black Metal Flake Finish)
Back to Index

F


CLAMP BLOCK-SKI BOAT IN BOARD
2-1/4" Stand-Off
SA27579P


(Heavy Duty with Black Metal Flake Finish)
Back to Index

G


SUPPORT TUBE
Aluminum SA27274P
Stainless Steel SA27275P
Back to Index

H


CLEVIS KIT-STAINLESS STEEL
With Short Bolt SA27314P
With Long Bolt SA27329P

NOTE: SA27313P Bushing should be ordered with SA27329P.
CLEVIS KIT-SKI BOAT (STAIN LESS STEEL)

With Short Bolt
SA27576P

With Long Bolt
SA27577P
Back to Index

NOTE: Parts shown on this page are available in kit form ONLY.

I


ROD END KIT
(1/2-20 THD.)
Steel SA27276P
Stainless Steel SA27277P
Back to Index

J


BUSHING KIT-IN BOARD TILLER ARM
SA27313P
Back to Index

M


SPENT TRAVEL TUBES FOR ROTARY HELMS

SAFE-T QC/
SAFE-T "TS"/
BIG-T Helms
SA35680P

NFB 4.2 /
NFB SAFE-T II /
HPS Rotary Helms
SA38603P
Back to Index

N


UNIVERSAL TIE BAR KIT
SA27252P

(Maximum length: 25-1/2")
Back to Index

O


CABLE GARD For Most Outboards with Tilt Tube
SA39329P

(Helps to keep the tilt tube clean.)
Back to Index

P


STEERING WHEEL HARD WARE KIT
2745417P

(For All Telefl ex Me chan i cal Helms with standard marine round 3/4" Tapered Shaft.)
Back to Index

Q


QC II HELM CONVERTER
For Helms with
Threaded Spigots

SA27620P

(Upgrades older Telefl ex rotary helms to Quick-Connect cable in ter face, allowing use of SSC61/SSC62 QC cables.)
Back to Index

R


HITCH PIN & TAG
FOR QUICK CONNECT HELM
AND QC II HELM CON VERT ER

2724514P

(Replacement hitch pin for all Telefl ex helms with the Quick Connect cable attachment port and for all Telefl ex SA27620P QC II Helm Converters.)
Back to Index

Morse Steering Connection Kits:

NOTE: Parts shown on this page are available in kit form ONLY.

  • SUPPORT TUBE
    (Aluminum) 064480
  • FRONT HOOKUP,
    OUTBOARD TRANSOM MOUNT

    (Galvanized) 300610
    (Stainless Steel) 300611
  • ADAPTER BRACKET
    for Johnson/Evinrude 40 hp and under
    300612
    (not pictured)

  • FRONT HOOKUP,
    OUTBOARD SPLASHWELL MOUNT

    300613
  • HOOKUP, INBOARD TRANSOM MOUNT
    for Volvo, 1977 and earlier
    300614
  • HOOKUP, INBOARD STAND-OFF
    Tall Bracket
    300616

  • HOOKUP, INBOARD STAND-OFF
    Short Bracket 2"
    300617

  • Short Bracket 2" (Stainless Steel)
    307046
    (See also Teleflex ski boat inboard clamp block kits on preceding pages.)

  • SWIVEL ASSEMBLY ONLY
    300618




JD on Facebook Live Tech Support JD Customer Photo Gallery Free Catalog