JD VIP Buyers Club
JD on Facebook
JamestownTV
JD Points Program
Request A Free Catalog

Electrical Glossary (F-K)


Technical reference from www.BlueSea.com


F


fast (fast acting) see also Delay
Refers to the amount of time that a fuse can endure an over-current before blowing. Fast fuses are used to protect sensitive equipment.

fault
A defect in the normal circuit configuration, usually due to unintentional grounding. Commonly referred to as a short circuit.

field
Typically refers to a magnetic field. Specifically used when discussing the rotating electo-magnetic field associated with an alternator. By varying the field current, thus its strength, the output of the alternator may be controlled.

float charge see also Bulk, Acceptance, Equalization
A constant voltage, well below the gassing point, that is applied to a battery to maintain its capacity. The voltage is such that neither charging nor discharging is occurring.

frequency see also Hertz
For an oscillating or varying current, frequency is the number of complete cycles per second in alternating current direction. The standard unit of frequency is the hertz, abbreviated Hz. If a current completes one cycle per second, then the frequency is 1 Hz; 60 cycles per second equals 60 Hz (the standard alternating-current utility frequency).

fuse
A fuse is a safety device, consisting of a strip of low-melting-point alloy, which is inserted in an electric circuit to prevent excess current from flowing. If the current becomes too high the alloy strip melts, opening the circuit.

fusible link
A type of fuse with a replaceable conductive alloy link that may be replaced if it "blows" due to over-current.



G

galvanic corrosion
The corrosion that occurs at the anode(s) of a galvanic cell.

galvanic isolator
A device installed in series with the (AC) grounding (green) conductor of the shore-power cable to effectively block low voltage DC galvanic current flow, but permit the passage of alternating current (AC) normally associated with the (AC) grounding (green) conductor. This is typically two diodes wired in parallel facing opposite directions, sized to meet full fault current.

galvanic series
A list of metals and alloys arranged in order of their potentials as measured in relation to a reference electrode when immersed in seawater. The table of potentials is arranged with the anodic or least noble metals at one end, and the cathodic or most noble metals at the other.

generator
A rotating machine capable of generating electrical power. In the narrow definition generator refers to a DC machine and alternator refers to an AC machine. However, in common use the term generator is used to refer to AC machines as well.

green wire
The green wire is the non-current carrying safety grounding wire in an AC system in the United States. It is connected to an exposed metal part in the electrical system to provide a path for fault current in the case of a short circuit.

ground fault
GFI (Ground Fault Interrupter)
GFI is generic term referring to both GFCI and GFP
GFCI (Ground Fault Circuit Interrupter) see GFI
A device intended for the protection of personnel that functions to de-energize a circuit, or portion thereof, within an established period of time when a current to ground exceeds some predetermined value that is less than that required to operate the overcurrent protective device of the supply circuit.
GFP (Ground Fault Protector) see GFI
A device intended to protect equipment by interrupting the electric current to the load when a fault current to ground exceeds some predetermined value that is less than that required to operate the overcurrent protection device of that supply circuit.

ground, ground conductor
A point in a circuit which is at zero potential with respect to the Earth, or which is at the lowest potential in the system, (as with a floating ground).

grounded
The AC current carrying conductor that is intentionally maintained at ground potential, also called neutral.

grounding, grounding conductor
The AC conductor, not normally carrying current, used to connect the metallic non-current carrying parts of electrical equipment to the AC system and engine negative terminal, or its bus, and to the shore AC grounding conductor through the shore power cable. This term can also refer to the normally non-current carrying conductor used to connect metallic non-current carrying parts of direct current devices to the engine negative terminal, or its bus, to minimize stray current corrosion.

ground plate
A conductive plate, commonly sintered copper, that is placed in contact with seawater to provide a connection to earth for a boat's ground systems.


H

Hertz
see Frequency
Hertz is a unit of frequency of one cycle per second. It replaces the earlier term of "cycle per second (cps)." The abbreviation for Hertz is Hz.

hot
Hot usually refers to the ungrounded current carrying conductors in an AC system. These would typically have a voltage of 120V or 240V in the United States. The term Hot is also used to describe a circuit that is energized, and has a potential greater than ground.


I

IACS
see International Annealed Copper Standard

Impressed current
Direct current supplied by a device employing a power source external to the electrode system of a cathodic protection installation. The impressed current is used to counteract the undesired galvanic current.

inductance
An effect in electrical systems in which electrical currents store energy temporarily in magnetic fields before that energy is returned to the circuit.

inductor see Coil
A length of wire that is wound around a core that is used as a storage element for a magnetic field in an electric circuit.

inrush
The momentary steep wave front of very high current exhibited by a load on initial application of power.

International Annealed Copper Standard
Abbreviated as IACS, this is a measurement of relative electrical conductivity that uses copper as the standard of 100%. The expression "Brass 28 IACS" would mean that the brass under discussion had 28% of the electrical conductivity of an identically sized piece of copper.

interrupt rating (AIC)
The fault current that a device, normally a fuse or circuit breaker is capable of breaking without damage.

inverter
An inverter converts DC power stored in a battery to AC power which is used by most household appliances.

ignition protection (IP)
Devices, which operate in a potentially explosive environment, must be ignition protected. This would include engine rooms with gasoline engines. There is a very specific set of tests which a device must pass to claim ignition protection. They include operating safely in an explosive mixture of propane and air.

isolation transformer
A transformer that is inserted in series with the incoming AC power to provide a magnetic coupling for power between the ship's systems and the AC grid. By magnetically coupling the power there is no direct connection by wires, which isolates the ships AC system from the AC grid.

isolator
Refers to two or more diodes wired in parallel and then inserted in series with the output of an alternator. This allows for the alternator to charge multiple batteries. The voltage drop across the diodes can cause incomplete charging. Isolators should not be used with alternators that use internal voltage sensing for regulation. To be properly installed the voltage sense lead must come from the house battery.


J, K

kilo
A prefix in the metric system equal to 1000 times, as in kilohertz, 1000 cycles per second.



Original article from Blue Sea Systems

JD on Facebook Live Tech Support JD Customer Photo Gallery Free Catalog