Interlux - Interfill 830 Fast Cure Epoxy Profiling Filler
Interlux Interlux
  • Interlux - Interfill 830 Fast Cure Epoxy Profiling Filler

Interlux - Interfill 830 Fast Cure Epoxy Profiling Filler

Interlux - Interfill 830 Fast Cure Epoxy Profiling Filler

A two-part epoxy filler that can be used above the waterline to the surface prior to applying topside finishes, and can be used to fill pinholes between coats of two-part polyurethanes, due to its ability to trowel to a very line, smooth finish. Interfill Epoxy Filler can also be used below the waterline to fill blisters and as part of a keel fairing system.

If Interfill Epoxy Filler is used below the waterline it must be overcoated with four coats of Interprotect 2000E/2001E. The cured epoxy has excellent solvent resistance and will not be attacked by the strong solvent in two-part polyurethanes or epoxies.

NOTE: Interfill 830 is a TWO PART epoxy. In order for this product to work properly, a Reactor (fast or standard cure) MUST be purchased in addition to the Base.

 
IN STOCK - Available for pickup  
$212.43 / ea
qty.   
$212.43
$212.43
 The item was added to your wishlist.
 The item was added to your shop cart.
Tech Spec Product Info User Generated Content
APPLICATION AND USE

Preparation

FIBERGLASS OR GELCOAT: Wipe with Fiberglass Solvent Wash 202. Sand with 80 grade (grit) paper. Remove sanding residue.

CLEAR EPOXY: Wash down with fresh water. Sand with 80 grade (grit) paper. Remove sanding residue.

EPOXY PRIMERS: Sand with 80 grade (grit) paper. Remove sanding residue.

Method Mixed putty is usually applied using a troweling knife (putty knife) with a 3 inch blade. Draw out to a thin layer. Do not apply more putty than necessary. After an overnight cure, sand with the same grade sandpaper being used for the overall surface area, then apply two-part primer or polyurethane.

Hints

Mixing Mix both components together thoroughly to correct mix ratio.

Thinner Reducing Solvent 2316N. Brush Thinner 2333N.

Thinning Thinning is not necessary in most situations. If thinning is required for very thin film applications, use Reducing Solvent 2316N. Alternatively Brush Thinner 2333N can be used. The addition of thinner will cause shrinkage of Interfill Epoxy Filler.

Cleaner Reducing Solvent 2316N. Brush Thinner 2333N.

Other If Interfill Epoxy Filler is used below the waterline, it must be covered by at least 4 coats of Interprotect 2000E/2001E.

Some Important Points Do not apply more than 800 mils thickness at any one time. Do not use below 10 C/50 F. Product temperature should be minimum 10 C/50 F and maximum 35 C/95 F. Ambient temperature should be minimum 10 C/50 F and maximum 35 C/95 F. Substrate temperature should be minimum 10 C/50 F and maximum 35 C/95 F.

Compatibility/Substrates Do not use on traditional wood constructions where the wood will expand and contract through changes in the moisture content.

Coverage (Theoretical) - 8.1 (sq ft/Gal) @ 5000 micron (200 mil) WFT.

Recommended DFT 787.4 mils dry

Application Methods Batten, Trowel

 

  • Colour YAV867-Gray
  • Specific Gravity 0.74
  • Volume Solids 100%
  • Mix Ratio 1:1 by volume (as supplied) , Converter/Curing Agent - YAV232
  • Typical Shelf Life 2 yrs
  • Unit Size 1 US Gallon (2 gallons mixed - Part A and Part B).
  • Area Above and below water
  • Method of application: Batten / Trowel

 

Drying Information  50 Degrees F  59 Degrees F  73 Degrees F  95 Degrees F 
Sandable  16 hrs  16 hrs  6 hrs  3 hrs 
Pot Life  50 Min  45 Min  35 Min  20 Min 
Overcoated By  Min-Max  Min-Max  Min-Max  Min-Max 
Barrier Kote  24 hrs-  24 hrs-  6 hrs-  6 hrs- 
Interprotect 2000E  24 hrs-  24 hrs-  6 hrs-  6 hrs- 
Interthane Plus  24 hrs-  24 hrs-  6 hrs-  6 hrs- 
TRANSPORTATION,STORAGE AND SAFETY INFORMATION

GENERAL INFORMATION: Exposure to air and extremes of temperature should be avoided. For the full shelf life of this product to be realised ensure that between use the container is firmly closed and the temperature is between 5 degC/40 deg F and 35 deg C/95 deg F. Keep out of direct sunlight.

TRANSPORTATION: Interfill Epoxy Filler should be kept in securely closed containers during transport and storage.

DISPOSAL: Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal.

GENERAL: Remainders of Interfill Epoxy Filler cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for in consultation with the authorities.

BRAND: Interlux
Material: Epoxy
Number Of Parts: Two Part
Rate Of Cure: Medium
Strength: Weak
Type: Fillers
3 1

REVIEW SNAPSHOT®

by PowerReviews
Interlux - Interfill 830 Fast Cure Epoxy Profiling Filler
 
3.0

(based on 1 review)

Ratings Distribution

  • 5 Stars

     

    (0)

  • 4 Stars

     

    (0)

  • 3 Stars

     

    (1)

  • 2 Stars

     

    (0)

  • 1 Stars

     

    (0)

Reviewed by 1 customer

Displaying review 1

Back to top

(3 of 3 customers found this review helpful)

 
3.0

a bit stiff

By pegasus

from Long Island NY

About Me Recreational

Verified Reviewer

Pros

  • Protects Well
  • Weather Proof

Cons

  • Too stiff

Best Uses

  • Indoor
  • Outdoor

Comments about Interlux - Interfill 830 Fast Cure Epoxy Profiling Filler:

This product works well, but its working consistency is a bit stiff to be able to smoothly fair the repaired area with the surrounding gelcoat. The overfill is a bit thick and requires some effort (sanding) to remove.

I prefer Interlux Watertite for filling small blemishes in the gelcoat - it goes on like mayonnaise and is easy to manage with a spatula.

Displaying review 1

Back to top

Related Items:
JD on Facebook Live Tech Support JD Customer Photo Gallery Free Catalog