SHO-HB12-6 -- 1/2 in x 6 ft TAC-S11-4500P12 -- 1/2 in x 12 ft SHO-HB34-6 -- 3/4 in x 6 ft SHO-HB1-6 -- 1 in x 6 ft TAC-S11-465OP12 -- 1 in x 12 ft SHO-HB114-6 -- 1-1/4 in x 6 ft TAC-S11-467OP12 -- 1-1/4 in x 12 ft TAC-S11-4690P12 -- 1-1/2 in x 12 ft
Type 304 marine grade stainless buffed polished predrilled and countersunk hollow back ovals on 6-inch centers. Uses flat or oval head fasteners. The 1/2in sizes use #6 fasteners, the 3/4in sizes use #8 fasteners, the 1in and 1 1/4in sizes use #10 fasteners. Sold in 6 and 12 foot lengths only.
Any continuous 12 length must be shipped motor freight.
$45.42
$63.13
$48.26
$70.54
$70.43
$80.96
$83.11
$141.96
$167.24
The item was added to your wishlist.
The item was added to your shop cart.
BRAND:
TACO
Metal:
Stainless Steel
Type:
Rub Rail
Questions & Answers about Hollow Back Half Ovals - Stainless Steel:
2012-05-17TOM DEACY asked: What is the typical length of #6 screw used for the half inch oval?
+Expand Answers
2012-05-17PETER DODGE: Half to three-quarter inch
2012-05-22KEVIN MACRITCHIE: Depends on the thickness of the substrate the oval is being fastened to and the amount of abuse the oval will see. I would think 3/4 inch may work, if it doesen't poke through the other side.
2012-06-11Gary Schoenfeldt: When I installed my Hollow Back Half Ovals I used 3/4" lg #6 Stainless Steel Oval Head Screws. As long as you have a good sound piece of wood to attach your Hollow Back Ovals to, the 3/4" long #6 screws should work well. You could always use longer screws if you run into a problem of not getting good anchorage.
Gary
2012-07-07THOMAS STEARNS: My choice for screw length to mount the half-round stainless strip depends on several factors so in my opinion there is no "typical" screw length.
Place the strip on the surface or edge that you're trying to protect. Then insert a screw of known length thru one of the mounting holes and measure how much protrudes above the half-round. This will give you a starting length, that is, how much length is needed before the screw sinks into the surface. Suppose you're mounting a 1/2" half-round on a flat surface: this length should come out about 1/2". Then consider what you're driving the screws into---if 1/2" wood, for example, an additional 1/4" or possibly 3/8" or so is all that can be used for a total length of 3/4" to 7/8". In no case should the screw length be long enough so the screw penetrates thru whatever you're mounting on----and keep in mind that there will be many screws holding the half-round in place and very little load on the assembly so there's no reason to use screws that penetrate more than 1/2" or so, in any case.
If you're mounting onto a sharp corner or edge on a keel or stem then screw length will shorten depending on how sharp the corner is---in the extreme case the starting length could be essentially zero.
2011-09-05R.D. R asked: Is your ss rub rail #sho-hb44-6-3/4in X 6ft available in 12' lengths? Please also give price and shipping cost.
+Expand Answers
2011-09-06Ryan L: It is only offered in 6' lengths.
Price Match Promise:
If you find a lower delivered price on a new identical item in stock and available for purchase from an authorized U.S. merchant.
- email us at pricematch@jamestowndistributors.com. This offer does not include special coupons or other promotional offers.
Special order items are not stocked and are ordered direct from the manufacturer. They are non-returnable, may take 2-4 weeks, price and shipping charges subject to change.
Checkout: 
Item(s) in your cart:
The item was added to your wishlist.
