Awlgrip Awl-Brite Converter J3006
Awlgrip Awlgrip Logo
  • Awlgrip Awl-Brite Converter J3006

Awlgrip AwlBrite Plus Converter

AwlGrip J3006 Converter - AWL-BRITE PLUS is a buffable, high build, three component clear urethane for marine brightwork. It provides a far more durable finish than varnish, is faster curing and as easy to apply. Do not use below the waterline.

The Awlbrite product line is based on a three component system, and so requires mixing the base with the converter and activator.

*** FOR PROFESSIONAL USE ONLY ***

Mix by volume 2 parts J3005 Base with 1 part J3006 Converter and 1/2 part A0031. A suggested mix is 4 oz. J3005 + 2 oz. J3006 + 1 oz. A0031= 7 oz. total. Additional A0031 can be added to help maintain a wet edge in warm weather, but the standard mix of 2:1:1/2 is required for proper cure. Mix only enough for one sealer coat. Apply one thin coat, allow to cure 8-12 hours.

 
IN STOCK - Available for pickup  
$55.02 / pt
qty.   
$55.02
$183.64
 The item was added to your wishlist.
 The item was added to your shop cart.
Tech Spec Product Info User Generated Content

 

  • Type: Three Component Acrylic Urethane
  • Packaging: 56 oz. kit, Half Gallons and Quarts
  • Theoretical Coverage: Sq. Feet/Gallon 930 Sq. Feet at 1 mil dry (25 microns) 93 Sq. Feet at recommended dry film thickness of 10 coats.
  • Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and environment.
  • Recommended Wet Film Thickness: 2.0-2.5 mils (50-62 microns) per coat.
  • Recommended Dry Film Thickness: 1.0-1.2 mils (25-30 microns) per coat.
  • Anticipated Cure Time at 77°F/50% R.H: 3 hours to recoat; 12 hours to light service; 7 days for full cure. Recoatability: With itself: 3 hours minimum, 36 hours maximum without sanding or scuffin

 

Application Info Apply with brush and roller.

Surface Preparation Wood should be clean, dry, smooth, and well seasoned. New Wood Use a marine teak wood cleaner or wood bleach to remove excess oils, promote uniformity, and adhesion. Follow manufacturer's instructions for use and thoroughly remove all cleaner and neutralizer residue before proceeding. Rough sawn lumber must be sanded to level the grain. Work grits to effectively level grain 60/80 to 100/150 to 220 etc. When grain is level, smooth sand with 320 grit paper.

Old finishes in good condition should be washed with AWL-PREP Surface Cleaner, then sanded with 220-320 grit paper to remove gloss. Old finishes in poor condition should be removed. Test on a small area to make sure Awl Brite Clear does not attack old finish. If old finish is attacked, it must be completely removed before continuing.

Mixing and Reduction Awl-Brite Clear is a component product. Mix by volume 2parts J3005 with 1 part J3006 until 1 smooth, homogenous mixture is obtained. Then add 1/2 part A0031. Overall mix is 2.1:1/2 by volume. Pot life is 1 to 2 hrs at 77 F/50% relative humidity.

Application Instructions
New Bare Wood Apply one light, smooth coat and allow to cure 8-12 hrs. Lightly sand with 320-400 grit paper to remove wicks and nubs before applying additional material.
General Apply light, smooth coats. Apply 2 coats in an 8 hr period. Allow to cure 8-12 hrs or overnight and repeat. Ten coats are recommended.

Sand as little as possible. Sanding is only required when/if product runs, sags, or brush marks need to be leveled. If dirt or grit must be removed from the surface, or if has been over 36 hrs since last application.

If no leveling is required, but it has been more than 36 hrs since last application, dull the surface with Scotchbrite pads. If possible, avoid curing or applying in direct sunlight. Do not apply or cure below 65 F.

Below Water Line (yes/no): No
BRAND: Awlgrip
Type: Converters
Related Items:
JD on Facebook Live Tech Support JD Customer Photo Gallery Free Catalog