Interlux Viny-Lux Primewash Primer
Interlux Interlux
  • Interlux Viny-Lux Primewash Primer

Interlux Viny-Lux Primewash Primer

Interlux 353/354 Viny-Lux Primewash is a two-part zinc chromate, vinyl butyral self etch primer, that is used as a metal conditioner for adhesion prior to application of other paints on metal.This product is best applied by spray, but can be applied by brush. Do not apply more than one coat.
This item is no longer available.
 The item was added to your wishlist.
 The item was added to your shop cart.
Tech Spec Product Info User Generated Content
APPLICATION AND USE

Preparation

Sandblast or grind to bright metal finish. Remove all blasting/grinding/sanding residues with a clean air line and sweep with a clean brush or broom. (Vacuum clean for best results.) Immediately apply Viny-Lux Primewash 353/354 thinned 25% with Viny-Lux Solvent 355.

Method Viny-Lux Primewash 353/354 is best applied by spray, but can be applied by brush. Apply one coat only.

Hints

Mixing Mix both components together thoroughly to correct mix ratio. Stir well before use. If small amounts are required, the mixing ratio by volume is 7 parts Viny-Lux Primewash Base 353 to 1 part Viny-Lux Primewash Reducer 354 to 2 parts Viny-Lux Solvent 355. Mix only as much as you can use in the stated pot life.

Thinner Viny-Lux Solvent 355

Thinning Thin Viny-Lux Primewash 353/354 25-30% with Viny-Lux Solvent 355.

Conventional Spray Pressure Pot: Pressure: 3.44-4.47 bar/50-65 psi (gun pressure); 8-10 psi (pot pressure). Tip Size: 0.89-1.4 mm/35-50 thou. Siphon Cup: Pressure: 3.44-4.47 bar/50-65 psi - gun pressure. Tip Size: 1.0-1.4 mm/40-50 thou.

Other Viny-Lux Primewash 353/354 must be overcoated within 24 hours of application. If more than 24 hours has elapsed, sand it off and reapply another coat.

Some Important Points Do not apply more than one coat. Do not apply in excess of 0.5 mils DFT. Excess film thickness will lead to delamination and splitting. Be careful not to leave puddles in deep sanding tracks. Do not use a cloth to remove blast residue as the cloth may leave fibers behind which can cause wicking of moisture through the primer system and cause premature failure. Product temperature should be minimum 10 deg C/50 deg F and maximum 29 deg C/85 deg F. Ambient temperature should be minimum 10 deg C/50 deg F and maximum 35 deg C/95 deg F. Substrate temperature should be minimum 10 deg C/50 deg F and maximum 29 deg C/85 deg F.

Compatibility/Substrates Apply over bare metal only. Metal surface must be thoroughly dry and free of all rust, mill-scale, grease, oil and paint. Sandblasting, power wire brushing and grinding with medium grade (grit) emery cloth are the best methods of cleaning. Do not use coarse sandpaper or grinding wheels.

Number of Coats 1 only

Coverage (Theoretical) - 425 (sq ft/Gal) by brush, 340 (sq ft/Gal) by spray

Recommended DFT 0.3 mils dry
Recommended WFT 4.0 mils wet

Application Methods Brush, Conventional Spray - Pressure Pot or Siphon Cup

 

  • Finish: Matte
  • Specific Gravity: 0.91
  • Volume Solids: 8%
  • Mix Ratio: 7-1 by volume (as supplied)
  • Typical Shelf Life: 2 yrs
  • VOC (As Supplied): 780 g/lt
  • Unit Size: 1 US QUART, 1 US GALLON
  • Number of Coats: 1 ONLY
  • Coverage (Theoretical) 425 (sq. ft./Gal) by brush, 340 (sq. ft./Gal) by spray
  • Touch Dry Time: 50 F - 30 min, 59 F - 30 min, 73 F - 30 min, 95 F - 30 min
  • Pot Life: 50 F - 8 Hrs, 59 F - 8 Hrs, 73 F - 8 Hrs, 95 F - 8 Hrs
  • Overcoating Time: 50 F - 1 hr min/24 hrs max, 59 F - 1 hr min/24 hrs max, 73 F - 1 hr min/24 hrs max, 95 F - 1 hr min/24 hrs max.

 

TRANSPORTATION,STORAGE AND SAFETY INFORMATION

TRANSPORTATION: Viny-Lux Primewash should be kept in securely closed containers during transport and storage.

STORAGE: Exposure to air and extremes of temperature should be avoided. For the full shelf life of Viny-Lux Primewash to be realised ensure that between use the container is firmly closed and the temperature is between 5 deg C/40 deg F and 35 deg C/95 deg F. Keep out of direct sunlight.

DISPOSAL: Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal.

Remainders of Viny-Lux Primewash cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for in consultation with the authorities.

Viny-Lux Primewash Reducer 354 contains Phosphoric Acid and must be handled with care.

BRAND: Interlux
Type: Primer
Users Also Bought:
JD on Facebook Live Tech Support JD Customer Photo Gallery Free Catalog