Interlux Jet Speed Varnish
Interlux Interlux
  • Interlux Jet Speed Varnish

Interlux Jet Speed Varnish

Interlux Jet Speed is quick drying for fast build up to two coats per day. Not recommended as an exterior finish coat. Jet Speed varnish does not contain UV protection, and must be finished (overcoated) with 1-2 coats & Plus 5 or Schooner, or another varnish that does provide UV protection.
This item is no longer available.
 The item was added to your wishlist.
 The item was added to your shop cart.
Tech Spec Product Info User Generated Content
APPLICATION AND USE

Preparation

BARE WOOD: Sand with 80 grade (grit) paper. Wipe with Brushing Liquid 333. Apply sealer coat of varnish reduced 10% with Brushing Liquid 333.

PREVIOUSLY VARNISHED WOOD: In Good Condition Sand surface with 120-150 grade (grit) paper and remove all dust. In Poor Condition If varnish is badly checked or peeling, remove finish to bare wood with Interstrip Semi-Paste 299E. Follow directions for varnishing bare wood.

Method Apply at least 5-6 coats on bare wood and a minimum of 3 coats on previously varnished surfaces until a satisfactory finish is obtained. Sand between coats using 220-320 grade (grit) paper. Remove sanding residue with a rag dampened with Brushing Liquid 333.

Hints

Thinner Brush - Brushing Liquid 333. Spray - Special Thinner 216.

Cleaner Bare Wood - Brushing Liquid 333.

Airless Spray Pressure: 170 bar/2500 psi. Tip Size: 0.33-0.41 mm/13-16 thou.

Conventional Spray Pressure Pot: Pressure: 3.44-4.47 bar/50-65 psi (gun pressure); 8-10 psi (pot pressure). Tip Size: 0.89-1.4 mm/35-50 thou. Siphon Cup: Pressure: 3.44-4.47 bar/50-65 psi - gun pressure. Tip Size: 1.5-1.8 mm/60-70 thou.

Other Spray pressures listed are recommendations only. The applicator may use any settings which yield the best results for the individual spraying technique and current weather conditions. To enhance appearance of the bare wood and fill porous open grain, apply Interstain according to label directions and allow to dry overnight.

Some Important Points Jet Speed is not recommended as an exterior finish and should be overcoated with a varnish that contains ultra-violet filters such as Schooner or Goldspar. Failure to follow proper dry times carefully will cause improper drying, wrinkling and loss of adhesion. Product temperature should be minimum 10 C/50 F and maximum 29 C/85 F. Ambient temperature should be minimum 10 C/50 F and maximum 35 C/95 F. Substrate temperature should be minimum 10 C/50 F and maximum 29 C/85 F.

Compatibility/Substrates Apply to clean, dry, properly prepared surfaces only. All sanded surfaces must be wiped clean with a cheesecloth dampened with Brushing Liquid 333 to remove sanding residue. Jet Speed can be applied over any varnish as long as it is adhered well and has been cleaned and sanded. Do not apply two part varnishes over Jet Speed.

Number of Coats At least 5-6 coats Bare Wood: Thin first coat 10% Previously Coated Wood: 3-4

Coverage (Theoretical) - 640 (sq ft/Gal) by brush, 510 (sq ft/Gal) by spray

Recommended DFT 1.2 mils dry

Application Methods Brush, Roller, Airless Spray, Conventional Spray - Pressure Pot or Siphon Cup

 

  • Finish: High Gloss
  • Specific Gravity: .88
  • Volume Solids: 49.5%
  • Typical Shelf Life: 2 yrs
  • VOC (As Supplied): 445 g/lt
  • Unit Size: 1 US Gallon
  • Number of Coats: At least 5-6 coats, Bare Wood Thin first coat 10%
  • Brush Coverage (Theoretical) - 640 (sq ft/Gal)
  • Spray Coverage (Theoretical) - 510 (sq ft/Gal)
  • Touch Dry Time: 50 F - 3 Hrs, 73 F - 2 Hrs, 95 F - 1 Hrs

 

Drying Information  50 Degrees F  73 Degrees F  95 Degrees F 
Touch Dry (ISO)  3 hours  2 hours  1 hour 
Overcoated By  Min-Max  Min-Max  Min-Max 
Jet Speed Varnish  6 hrs-  5 hrs-  4 hrs- 
TRANSPORTATION,STORAGE AND SAFETY INFORMATION

TRANSPORTATION: Jet Speed should be kept in securely closed containers during transport and storage.

STORAGE: Exposure to air and extremes of temperature should be avoided. For the full shelf life of Jet Speed to be realised ensure that between use the container is firmly closed and the temperature is between 5 C/40 F and 35 C/95 F. Keep out of direct sunlight.

DISPOSAL: Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal. Remainders of Jet Speed cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for in consultation with the authorities.

BRAND: Interlux
Rate Of Cure: 1 Day
Type: Varnishes
Users Also Bought:
JD on Facebook Live Tech Support JD Customer Photo Gallery Free Catalog