We are committed to delivering
the perfect order - on time and hassle free.
Fast and reliable -- Jamestown Distributors will ship anywhere in the world.
Rule Hose Designed for use with Rule pumps. All sizes have smooth mounting cuffs every 12-inches. Flexible for easy installation and resistant to acid, detergents, oil, gasoline, diesel, fuel, and salt water. Corrugated white polyethylene bilge hose is formulated with the end user in mind. Used in Vanguard 15 Bilges exclusively.
$0.98
$0.74
$1.11
The item was added to your wishlist.
The item was added to your shop cart.
BRAND:
Rule Industries
Type:
Bilge Pump Hose
Questions & Answers about Rule Bilge Pump Hose:
2012-07-20A shopper asked: if I order 10 feet of hose, does it come as one piece or in 10 one foot sections? ... thanks
+Expand Answers
2012-07-20Ryan L: It will come as one 10 foot section.
2012-05-23JUDI MOHLER asked: do I match sizes of hoses and thru hull fittings by just using the same diameter? In other words, if the measurement on the thru hull fitting is 1 1/8" then I get the pump hose at 1 1/8" also. Want to get it right the first time I order.
+Expand Answers
2012-05-24ROBERT ASHABRANNER: Yes, you are correct, match hose ID to OD of the thru hull fitting, so for the 1-1/8" thru hull the correct hose ID is 1-1/8"
2012-05-24MATTHEW COHEN: Correct. I believe that this hose is measured by the ID (inside diameter). If you order 1 1/8 hose that means it should fit over a 1 1/8 fitting.
2012-05-24FRANK GUIDO: Yes you get a hose diameter that is the same as the barb fitting on the threw hull. It's a tight fit and you will have to push with some force but the hose will stretch around the barb.
2012-05-24WILLIAM MOHRMAN: Hose is measured on the inside diameter of the hose. 1 1/8" is the inside diameter of the hose. However, when measuring your thru hull fitting, you measure the fitting neck where the hose would clamp onto the fitting past the barb (flaired end where you shove the hose over). This measurement should be a slightly bigger than 1 1/8" to allow for a snug fit.
You can also measure the inside diameter of the thru hull fitting, but you will find this to be somewhat smaller than 1 1/8" due to the wall thickness of the fitting.
2011-10-03PHIL SIGMUND asked: Is there an adapter to go from rul-80 (1-1/8) to standard 1-1/4 plumbing fittings?
+Expand Answers
2011-10-04MORRIS CALI: This hose is intended as a bildge pump discharge hose and should be routed from a bildge pump discharge to a through hull fitting or grey water discharge above the warter line only, that is why it is so cheap. If you are connecting a sink to a thru hull fitting below the waterline you need to use a good quality hose such as bellowsflex that can be purchased a a local industrial hose distributor, It is wire wound which keeps it from collapsing plus it is tough and is not subject to bending or breaking. If you want to sink your boat use the cheaper hose but it is not designed to be used under the water line.
Comments about Rule Industries Rule Bilge Pump Hose:
Fits the Attwood Tsunami 1200 GPH Bilge Pump. These Hoses are not easy to find. I am very greatful that JD had it!
2/25/2010
(1 of 1 customers found this review helpful)
5.0
Best place to buy this hose!
By goldrushpro
from Boise Idaho
About Me Professional
Pros
Durable
Easy To Install
Cons
Best Uses
Any low preasure app
Comments about Rule Industries Rule Bilge Pump Hose:
[...]
9/30/2009
(1 of 1 customers found this review helpful)
1.0
Pump cycling causes leaks over time.
By guyrj33
from North of Boston
About Me Avid Do-It-Yourselfer
Pros
Cons
Flimsy
Leaks
Best Uses
Comments about Rule Industries Rule Bilge Pump Hose:
I suggest using smooth bore reinforced hose.
6/23/2009
4.0
Works well for an array of uses
By Tall boy
from Ohio
About Me Avid Do-It-Yourselfer
Pros
Durable
Easy To Install
Cons
Flimsy
Best Uses
Boats
Swimming pool pumps
Comments about Rule Industries Rule Bilge Pump Hose:
I have used this hose for bilges on Boats as well as swiming pool pumps and seems to hold up very well.
6/21/2009
3.0
Don't "Set It and Forget It"
By captqrunch
from hill country, texas
About Me Avid Do-It-Yourselfer
Pros
Easy To Install
Easy To Use
Cons
Best Uses
Comments about Rule Industries Rule Bilge Pump Hose:
After about 10 years, the aging hose cracked at the cuff where it was clamped to the emergency bilge pump. I doubt any liquid had ever passed through it nor had it ever seen any sunlight. This sort of subtle failure could easily result in the loss of a boat. If you install this hose, best to check its condition annually.
8/28/2008
(1 of 1 customers found this review helpful)
4.0
Fits the bill
By rbensyl
from Atl, GA
About Me Handyman
Pros
Easy To Install
Easy To Use
Cons
Best Uses
Comments about Rule Industries Rule Bilge Pump Hose:
this product economically fits the bill for longer runs of tubing - very light and easy to install. Time will tell how durable it ends up being
Price Match Promise:
If you find a lower delivered price on a new identical item in stock and available for purchase from an authorized U.S. merchant.
- email us at pricematch@jamestowndistributors.com. This offer does not include special coupons or other promotional offers.
Special order items are not stocked and are ordered direct from the manufacturer. They are non-returnable, may take 2-4 weeks, price and shipping charges subject to change.
Checkout: 
Item(s) in your cart:
The item was added to your wishlist.
