Weld Mount Mixing Tips
Weld Mount Weld Mount
  • Weld Mount Mixing Tips
  • Weld Mount Installation
  • Weld Mount samples

Weld Mount Mixing Tips

Weld Mount Mixing Tips (or nozzles) provide precise mixing and dispensing of Weld Mount adhesives.

AT-400 3.5" Adhesive Mixing Tip is for use with the AT-2010 Adhesive. This mixing tip is designed with a specific number of mixers to ensure a fully mixed adhesive.

AT-450 3.5" Adhesive Mixing Tip is designed for use with the high viscosity AT-4020 Adhesive. A correct number of mixers are required to dispense a fully mixed adhesive.

AT-650 5.0" Adhesive Mixing Tip is for the AT-6030 adhesive. AT-6030 is A 10-to-1 adhesive which requires a longer mixing tip with extra mixing chambers. We recommend cutting of the tip prior to use to minimize back pressure when dispensing.

We recommend (5) Mixing Tips for each cartridge of adhesive.

NOTE: Mixing Tips must be used with an AT-300 dispensing gun.

Sold in (10)(50) packs

 
IN STOCK - Available for pickup  
$15.78 / pk
qty.   
$15.78
$67.73
$15.78
$67.73
$15.78
$67.73
 The item was added to your wishlist.
 The item was added to your shop cart.
Tech Spec Product Info User Generated Content

Weld Mount System advantages:

  • Eliminate the need to drill in to a composite skin and exposing the core
  • Eliminate drilling, tapping, welding, grinding and finishing steps
  • Eliminate costly rework expenses caused by inadvertently drilling though substrates
  • Eliminate blocking added during lamination in order to have a place to put screws
  • Much stronger than traditional methods

 

Description of the WELD MOUNT ADHESIVES

AT-1030 Is A specially formulated acrylic adhesive which cures in 12 minutes and has working strength within 40 minutes. AT-1030 is packaged in a 30 ML side by side dispenser cartridge with a built in plunger. Cut off the tips and dispense the amount needed for hand mixing. A cap is included to deal the cartridge for reuse. AT-1030 is a good general purpose bonder for all substrates except low energy plastics and rubber. AT-1030 has a shelf life of 12 months when stored at 72 degrees or less. The cartridge will bond 50-75 parts.


AT-2010 is also a two-part acrylic adhesive, which is formulated with high viscosity to allow instant bonding of Weld Mount System fasteners to any surface (horizontal, vertical or overhead). AT-2010 is packaged in a two part 50 ML cartridge which is mounted in the AT-300 adhesive dispensing gun using a 1 to 1 plunger. A special mixing tip is used to mix the two components thoroughly before use. AT-2010 sets in approximately 6 minutes, develops working strength in 15-20 minutes and dries to a light yellow color. AT-2010 is used typically for bonding Weld Mount parts in lighter duty applications.


AT-4020 acrylic adhesive will bond to fiberglass, steel, aluminum, glass, wood and many other substrates. However, it should be noted that AT-4020 adhesive will not bond well to StarBoard, low energy plastics or rubber. AT-4020 does not adhere as well to metals as it does to composite substrates. Weld Mount AT-4020 Acrylic Adhesive is a specially formulated to hold studs and standoffs without sagging. The Acrylic Adhesive cures in 10 minutes and has a working strength within 30 minutes at 72 Degrees F. The 50 ML cartridge will bond approximately 100-150 parts. AT-4020 is used primarily for bonding Weld Mount parts to composites in heavier duty applications.


AT-6030 adhesive is a two-component, 10:1 mix ratio structural adhesive with outstanding adhesion for bonding metals, carbon fiber, composites and most plastics. Most metals can be bonded without priming. This advanced product is designed to meet specific requirements of the transportation industry, including reduced read through on show surfaces. The combination of minimum surface preparation, primerless metal bonding and low read through makes AT-6030 ideal for a variety of assembly operations. AT-6030 is packaged in 40ML cartridges for use with our AT-300 dispensing gun and AT-650 mixing tips. AT-6030 is used typically for bonding Weld Mount parts in the heaviest duty applications.

BRAND: Weld Mount
Type: Mixing Tips
Users Also Bought:
JD on Facebook Live Tech Support JD Customer Photo Gallery Free Catalog