Weld Mount Complete Wire Tie Kit with Gun
Weld Mount Weld Mount
  • Weld Mount Complete Wire Tie Kit with Gun
  • Weld Mount Installation
  • Weld Mount samples

Weld Mount Complete Wire Tie Kit with Gun

The Weld Mount Wire Tie Mount Kit is ideal for primary wire and cable runs, submerged bilge wire and hose bundles, as well as securely mounting firewall and bulkhead wiring. The Weld Mount Wire Tie Mounts may be attached to virtually any surface.

The Weld Mount Fastening System removes the need to install screws into or through cored substrates thus eliminating a major cause of composite delamination.

 
IN STOCK - Available for pickup  
$173.15 / kt
qty.   
$173.15
$139.28
 The item was added to your wishlist.
 The item was added to your shop cart.
Tech Spec Product Info User Generated Content

The Weld Mount Wire Tie Mounts are designed to be bonded with Weld Mount AT-4020 Adhesive. The Weld Mount Wire Tie Mounts may also be set directly into wet resin during hull lay up.

The Weld Mount AT-4020 Acrylic Adhesive will bond to Fiberglass, Steel, Aluminum, Glass, Wood and many other substrates. However, it should be noted that the Weld Mount adhesive will not bond well to StarBoard, low energy plastics or rubber.

The Weld Mount AT-4020 Acrylic Adhesive is a specially formulated to hold wire tie mounts without sagging. The Acrylic Adhesive cures in 10 minutes and has a working strength within 30 minutes at 72 Degrees F. The 50 ML cartridge will bond approximately 100-150 parts.

AT-3 White Nylon Wire Tie Mounts are sized for a number 3 wire tie. The square base measures 9/16 inch square. The average pull strength is approximately 50 lbs. Use the AT-3 wire tie mounts for smaller wire runs or where space prevents the use of larger mounts.

AT-5 White Nylon Wire Tie Mounts are sized for a number 5 wire tie. The large base measures 1-1/8 inches long x 3/4 inches wide. The average pull strength is approximately 150 lbs. Use the AT-5 wire tie mounts for heavier wire runs or where space permits the use of the larger mounts.

50100 Kit Contains:

  • (100) AT-5 White Tie Mounts
  • (50) AT-3 White Tie Mounts
  • (1) AT-4020 White Adhesive
  • (5) AT-450 Mixing Tips
  • (1) AT-300 Adhesive Gun
  • Step By Step Instructions

50109 Kit Contains: All of the above without adhesive.


Description of the WELD MOUNT ADHESIVES

AT-1030 Is A specially formulated acrylic adhesive which cures in 12 minutes and has working strength within 40 minutes. AT-1030 is packaged in a 30 ML side by side dispenser cartridge with a built in plunger. Cut off the tips and dispense the amount needed for hand mixing. A cap is included to deal the cartridge for reuse. AT-1030 is a good general purpose bonder for all substrates except low energy plastics and rubber. AT-1030 has a shelf life of 12 months when stored at 72 degrees or less. The cartridge will bond 50-75 parts.


AT-2010 is also a two-part acrylic adhesive, which is formulated with high viscosity to allow instant bonding of Weld Mount System fasteners to any surface (horizontal, vertical or overhead). AT-2010 is packaged in a two part 50 ML cartridge which is mounted in the AT-300 adhesive dispensing gun using a 1 to 1 plunger. A special mixing tip is used to mix the two components thoroughly before use. AT-2010 sets in approximately 6 minutes, develops working strength in 15-20 minutes and dries to a light yellow color. AT-2010 is used typically for bonding Weld Mount parts in lighter duty applications.


AT-4020 acrylic adhesive will bond to fiberglass, steel, aluminum, glass, wood and many other substrates. However, it should be noted that AT-4020 adhesive will not bond well to StarBoard, low energy plastics or rubber. AT-4020 does not adhere as well to metals as it does to composite substrates. Weld Mount AT-4020 Acrylic Adhesive is a specially formulated to hold studs and standoffs without sagging. The Acrylic Adhesive cures in 10 minutes and has a working strength within 30 minutes at 72 Degrees F. The 50 ML cartridge will bond approximately 100-150 parts. AT-4020 is used primarily for bonding Weld Mount parts to composites in heavier duty applications.


AT-6030 adhesive is a two-component, 10:1 mix ratio structural adhesive with outstanding adhesion for bonding metals, carbon fiber, composites and most plastics. Most metals can be bonded without priming. This advanced product is designed to meet specific requirements of the transportation industry, including reduced read through on show surfaces. The combination of minimum surface preparation, primerless metal bonding and low read through makes AT-6030 ideal for a variety of assembly operations. AT-6030 is packaged in 40ML cartridges for use with our AT-300 dispensing gun and AT-650 mixing tips. AT-6030 is used typically for bonding Weld Mount parts in the heaviest duty applications.

Weld Mount System advantages:

  • Eliminate the need to drill in to a composite skin and exposing the core
  • Eliminate drilling, tapping, welding, grinding and finishing steps
  • Eliminate costly rework expenses caused by inadvertently drilling though substrates
  • Eliminate blocking added during lamination in order to have a place to put screws
  • Much stronger than traditional methods

 

BRAND: Weld Mount
Material: Methacrylate
Type: Cable Ties and Clamps
4 1

REVIEW SNAPSHOT®

by PowerReviews
Weld Mount Complete Wire Tie Kit with Gun
 
4.0

(based on 1 review)

Ratings Distribution

  • 5 Stars

     

    (0)

  • 4 Stars

     

    (1)

  • 3 Stars

     

    (0)

  • 2 Stars

     

    (0)

  • 1 Stars

     

    (0)

Reviewed by 1 customer

Displaying review 1

Back to top

 
4.0

The right way to mount cables and wires

By Sam

from Chesapeake, VA

About Me Tech Savvy

Staff Reviewer

Pros

  • Bonds great
  • Fits Multiple Cable Sizes
  • Very strong adhesive

Cons

  • None

Best Uses

  • Automotive
  • Boat building

Comments about Weld Mount Complete Wire Tie Kit with Gun:

The Weldmount adhesive is a great bonding goop. It really bonds like iron to any solid surface. The wire tie bases are many times stronger than the usual plastic self stick bases. The Weldmount bases when bonded with their glue will support very heavy cables and wire bundles.

  • Primary use:
  • Personal

Displaying review 1

Back to top

Related Items:
JD on Facebook Live Tech Support JD Customer Photo Gallery Free Catalog