Interlux - Interdeck Polyurethane Non-Skid Deck Coating

Interlux - Interdeck Polyurethane Non-Skid Deck Coating

An excellent, easy to apply slip resistant polyurethane finish for decks.

Interdeck contains a fine aggregate and will apply easily on all substrates.

Interdeck gives a low sheen finish that helps protect against dazzle from sunlight reflected off decks.

The tough polyurethane resin protects decks against everyday wear and tear.

Suitable for all substrates.

NOTE: Due to differences in monitors the colors shown on this page may not represent actual paint color.

Request a free copy of the "Interlux Boat Painting Guide and Color Card". This booklet will guide you through the full Interlux product range and provide you with product application instructions.

APPLICATION AND USE

Preparation

PREVIOUSLY PAINTED SURFACES:

In Good Condition: Wash down with Yacht Line Super Cleaner, rinse with fresh water and allow to dry. Abrade with 280-320 grade (grit) paper.

In Poor Condition: Remove all previous coatings and prime the substrate.

PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet.

BARE WOOD: Prime with Yacht Primer or UCP.

STEEL: Prime with Yacht Primer or Interprotect.

ALUMINIUM: Prime with Etch Primer followed by either Yacht Primer or Interprotect.

GRP: Wash down with Yacht Line Super Cleaner, rinse with fresh water and allow to dry. Abrade with 180-220 grade paper. No priming necessary. - If any filling is required use the appropriate product from the Interfill range.

Method Sand the primer with 180-220 grade wet or dry paper. Remove dust with a dust wipe. Apply 1-2 coats.

Hints

Mixing Stir well before use.

Thinner Thinners No.1 (YTA800)

Cleaner Thinners No.1 (YTA800)

Ventilation and Humidity Control Apply in dry, well ventilated conditions.

Other For best results either stipple by brush or use a mohair roller.

Some Important Points Product temperature should be minimum 10 deg C and maximum 30 deg C. Ambient temperature should be minimum 5 deg C/40 deg F and maximum 35 deg C/95 deg F. Substrate temperature should be minimum 5 deg C/40 deg F and maximum 35 deg C/95 deg F.

Compatibility/Substrates Suitable for all substrates and filled surfaces. Not suitable for permanently immersed surfaces. Do not clean with highly alkaline cleaners.

Number of Coats 1-2

Coverage (Theoretical) - 386.7 (sq ft/Gal)

Recommended DFT 2.0 mils dry
Recommended WFT 3.7 mils wet

Application Methods Brush, Roller

Finish: Low Sheen
Specific Gravity:1.4
Volume Solids:54%
Typical Shelf Life:2 yrs
Unit Size:1 US QUART
Number of Coats:2 minimum
Brush Coverage:(Theoretical) 386.7 (ft²/Gal)
Spray Coverage:(Theoretical) 40 (ft²/Gal)
Touch Dry Time: 41°F-5Hrs, 59°F-4Hrs, 73°F-3Hrs, 95°F-2Hr
Walk-On Dry Time: 41°F-4 Days, 59°F-3 Days, 73°F-2 Days, 95°F-1 Day

Drying Information	41 degrees F	59 Degrees F	73 Degrees F	95 Degrees F
Touch Dry (ISO)	5 hours	4 hours	3 hours	2 hours
Dry to Walk On	4 days	3 days	2 days	1 day
Overcoated By	Min-Max	Min-Max	Min-Max	Min-Max
Interdeck	24 hrs - 4 days	20 hrs - 3 days	16 hrs - 2 days	12 hrs - 1 day

TRANSPORTATION, STORAGE AND SAFETY INFORMATION

GENERAL INFORMATION: Exposure to air and extremes of temperature should be avoided. For the full shelf life of Interdeck to be realised ensure that between use the container is firmly closed and the temperature is between 5 deg C/40 deg F and 35 deg C/95 deg F. Keep out of direct sunlight.

TRANSPORTATION: Interdeck should be kept in securely closed containers during transport and storage.

DISPOSAL: Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal. Remainders of Interdeck cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for in consultation with the authorities.