We are committed to delivering
the perfect order - on time and hassle free.
Fast and reliable -- Jamestown Distributors will ship anywhere in the world.
Quikfair Fairing Compound is a lightweight microballoon-filled fast-curing two-part epoxy fairing putty with excellent moisture resistance. Designed to be used on both fiberglass and wood-epoxy boats above or below the waterline.
$27.99
$27.99
$38.99
$38.99
$71.99
$71.99
$134.99
$134.99
The item was added to your wishlist.
The item was added to your shop cart.
Technical Specifications
Mix Ratio by Weight: 2:1
Total Solids: 100 percent
Mixed Viscosity
Mixed Color: Tan
Pot Life at 77 degrees F: 10 Minutes
Tack Free Time at 77 degrees F: 3 Hours
Hand Sand in 3 hours
Machine Sand in 4 hours
Use protective gloves when working with this product. Use soap and water or white vinegar to clean off of your hands. Use Denatured Alcohol to clean off your tools.
BRAND:
System Three
Material:
Epoxy
Number Of Parts:
Two Part
Rate Of Cure:
Fast
Type:
Fairing Compounds
Questions & Answers about System Three QuikFair Fairing Compound:
2013-04-02MIKE RUSSELL asked: will this adhere well to lead keels and is there any kind of primer I have to use before or after using this on my keel?
+Expand Answers
2013-04-05JIM PRETTYMAN: I used this compound to fair small portions of the hull on a wooden boat so I cannot answer your specific question.
2013-02-03A shopper asked: Can, or do you use a foam brush after applying with a spreader to get a completely smooth application? I'm using this product on a large (4' long) wooden ship model to seal & finish the hull. Since the shape includes many rounded areas my skill level with a spatula application leaves many highs & lows. I need a much smoother application & thought a foam brush might be the answer. Any help for this rookie would be appreciated.
Thanks
+Expand Answers
2013-02-04STEVE LOCKHART: I have used the product but not with a foam brush. I use the plastic spreaders available with "Bondo" product.
2013-02-04DAN HOUSTON: The material is too thick to use a foam brush with. A plastic putty knife works best . You will need to sand and paint the hull. Sanding will give a very smooth finish. You might try sanding with foam blocks if you have unusual shapes.
2013-02-04JEFF ILSE: That might help, but the stuff is thick enough that it will probably leave drag marks. It is really easy to sand though, so if the contours allow for sanding, just plan on sanding it all smooth.
2013-02-04JOSEPH ANTIN: it is like putty when mixed. i honestly doubt you can use a foam brush. Normally this product is used to raise low spots before definitive sanding. It is like using Bondo on a car. It is easier to sand than hardwood so you have to be careful about oversanding that spot.
2013-02-05KENNETH KASSLER-TAUB: I am not an expert, but the material is a bit thick and sticky for a foam brush, sort of like soft taffy or peanut butter. Have you thought about using an old credit card or plastic hotel room key for a smoother finish? It may give you more flexibility and control than a spatula.
2013-02-05MAURICE DUNIGAN: I have always used plastic spatula's and have never tried a foam brush. I am going to repair the hull that has damage and will try the foam to see if it works. Anyway this is a good thought
2013-02-05DAVID HALL: You can use a damp foam pad to smooth out the surface. It will still have small ridges from the foam after it cures (24 to 48 hrs). QuickFair sands very easily, just use a sanding block so you do not dig trenches when you sand. You will need to add a thin coat of sealer once you have the shape you want. Make sure your done sanding because when the quickfare soaks up the sealer it gets dificult to sand. I usually seal with a 50/50 mixture of epoxy resin and thinner, it will brush on fairly smooth and the quick fare soaks it up like wood. After your first coat of sealer you can wet sand with some 240 grit then follow up with 400. After your second coat of sealer you can get by using only 400. I have found that the epoxy sealer will accept almost any paint.
2013-02-05GARY MEARS: QuickFair is an epoxy product premixed with fillers in both the resin and the hardener, so by mixing in the right amounts you end up with a thick compound that is abought the consistency of peanut butter. To apply it to your model hull I would use some squeeges of some sort and put on multiple layers sanding in between. The product hardens fast and you should be able to do multiple coats in a day. Because of the fillers used, it sands very easily, but doesn't leave a real smooth finish without sanding it out. A foam brush is not going to work, but on the inside of most foam brushes is a piece of plasic that can be used as a smaller sqeege. I make custom spreaders out of alot of things to reach into areas that a regular spreader won't fit, like milk jugs or even cutting down the heavy spreaders used for body putty. Hope this helps.
2013-02-05RICHARD SCHAIRER: I have never used a foam brush so I do not know if this will work, however sys 3 fairing compound sands very easy and you should be able to get a very smooth finish.
2013-02-09GARY SCHWARZMAN: Quickfair is too stiff to be smoothed with a foam brush. You need to be prepared to sand it smooth.
2012-10-20JIM KEA asked: what is the coverage for this product? I want to use as fairing on hull of old plywood boat.
+Expand Answers
2012-10-22SHAWN IVIE: I would only use this product for small areas of imperfection. Works great for final fairing before primer and paint.
2012-10-22ROBERT PATERSON: Not sure of coverage from total amount. I use it in spotting situations. Seems like a substitute for bondo kinds of products, except doen't harden as fast...but is epoxy/not polyester filler. I use if mostly in fairing of an iron keel on a Rhodes 19.
2012-10-23JOHN STAX: I can help with that. I re surfaced my 23' Lyman, made of plywood, winter before last. The Quick Fair stuff is very expensive compared to mixing West with fairing fillers. My guess is you would never finish the job properly, just too much money. I got great results starting with major sanding, then Smith's penetrating epoxy to coats applied with mini foam roller, then West epoxy then thickened West , then sanding some more.
I used the boat a lot this summer and it held up without a single crack or fault, so all this talk about epoxy being brittle is doubtfull.
2012-10-02KEVIN MARKS asked: Will this hold up to beach abrasion or boat launch impacts on the bottom edge of Hobie Cat hulls? If not, what top coat would you recommend?
+Expand Answers
2012-10-03JEFF ILSE: I don't think so. It's designed for easy sanding and making smooth pretty surfaces. The fact that it sands so easily can tell you what would happen if you hit a beach. You could top coat it with a hard two part polyurethane paint, but that would also need some touching up after encounters with the beach.
If you're looking just to protect your hulls, possibly a kevlar felt and epoxy would be more appropriate.
2012-10-03DOUG LOGAN: Kevin,
It should hold up fine against moderate abrasion. Most of the boats are made of 10% fairing compound. That number is declining the better I get:)
2012-10-04G LESLIE BURNETT: Hi Kevin. Re. abrasion on the bottom of a Hobie Cat.
This product is excellent for filling scratches and hollow spots, but I would not use it for the what you are thinking of. With the boat upside down build up the area with glass and polyester (or better yet epoxy) resin. This may take several steps then sand to the shape you want and then use "QuickFair" to make the surface smooth. After you are done prime with a two part primer (Jamestown can suggest a product).
notes.
clean the surfaces (do not use any soap)
mask the area with tape and plastic
work clean
ware a mask!!!
2012-10-04CHOPTANK BOATWORKS PATRICK MERTAUGH: QuickFair is really designed as a relatively soft, easy sanding fairing compound for non-structural filling (in my opinion). I would use an epoxy of your choice filled with silica, or another high density eboxy filler/thickener. It'd be even better if you could get a layer of fiberglass or dynel over it to add to the abrasion resistance.
2012-10-04GARY JONES: If you consider that this is a sandable product, beach abrasions will wear it down. However, this product is epoxy and will take a beating equalt to your fiberglass bottom.
2012-10-05DAN HOUSTON: This material while fairly hard is not going to be as hard as the hull was.
You could use it and wet it out with epoxy and glass over it but it will abraid.
It is easy to sand and will fill all imperfections.
2012-08-28MIKE M asked: Which step first on my new wooden hull-- System 3 QuikFair or Primer paint??
+Expand Answers
2012-08-28ROBERT SIMMONS: In most instances I would suggest that all modeling and repairing including fairing be done before beginning the finishing process.
2012-08-28mike m: Thank you for your time and advice.
While we are on the subject, any recommendations on paint ? I want a traditional look, this boat is similar to the Pulsifer Hampton. I see Mr. Pulsifer notes his Epifanes hull color, but not the type paint--
One part Alkyd or Epoxy primer??
One component topcoat or Two component??
2012-08-28CHOPTANK BOATWORKS PATRICK MERTAUGH: QuickFair first if needed for fairing. Apply QuickFair to bare wood or sanded epoxy not paint. Suggest a 2 part primer over QuickFair if you want it to cure at a reasonable rate. Then a one or two part paint.
2012-08-28mike m: Thank you for your time and advice.
While we are on the subject, any recommendations on paint ? I want a traditional look, this boat is similar to the Pulsifer Hampton. I see Mr. Pulsifer notes his Epifanes hull color, but not the type paint--
One part Alkyd or Epoxy primer??
One component topcoat or Two component??
2012-08-29CHOPTANK BOATWORKS PATRICK MERTAUGH: If the boat is traditionally built with solid wood planking without an epoxy or glass sheathing, I'd suggest a one part primer like interlux pre-kote. It has a high build and is generally easy to sand without loading the paper. If the hull is cold-molded and/or sheathed in epoxy and/or glass, I'd use a 2 part primer like Awl-grip 545. As far a top coat paint, I'm a fan of Interlux Brightsides for either type of construction. You can add some of the brands flattener if you'd like a bit less gloss. I've used Kirby's topcoat paints as well because they have some great classic colors, but I don't think it's as durable as Brightsides. I get good finishes rolling and tipping Brightsides with a foam roller and foam brush. 2 part topcoats are very durable and long lasting, but are a bit finicky to apply, somewhat dangerous to your health, and most of the time overkill.
2012-08-28JAY GRAHAM: I would use a coat or two of Smiths penetrating epoxy over the new wood. Then fair with the quick fair. I use West System most of the time but I find it handy to have some quick fair on the shelf. It sands very easy.
2012-08-29GARY MARKHAM: Quick fair first then primer would be my choice. The primer is to prepair the surface for the paint. You can call the paint manufacturer and verify.
2012-09-02RANDY COLKER: I would think the quick fare as it is thicker, and I would think it would be the first step. My experience is that it adheres quite well. Great stuff. Just make sure that it doesn't get hot and harden before you get a chance to use it. I've lost several dollars worth that way. Make small batches and spread it out.
2012-03-21A shopper asked: WHAT COLOR IS THIS PRODUCT?
+Expand Answers
2012-03-21RICHARD APPLEGET: IT DRIES TO A LIGHT BIEGE AND I FOUND IT VERY EASY TO USE
2012-03-21JEFF ANDREWS: The color is kind of a light 'peach' or tan.
2012-03-21KEVIN MACRITCHIE: cures to a light gray, sands easily but must be coated for UV protection.
2012-03-22GARY JONES: It dries to a tan color.
2012-03-22WILLIAM GRAESER: white
2012-03-22GEORGE HOSPODAR: Beige or tan.
2012-03-26MATT HUMMEL: I donâ??t remember the hardener being as yellow as it is now when it was new. Just mixed up a small batch to show final color. Pretty much a silly putty color.
2011-10-21MICHAEL CAPONIGRO asked: Can you add color to Sys 3 Quick Fair?
+Expand Answers
2011-11-01JEFF HOEPFL: I guess you could? It mixes to a tanish-pink color. You should paint it or gel coat it for UV protection.
Comments about System Three QuikFair Fairing Compound:
Faired the bottom diagonal planking seams on my 18' cold molded Hydrotec plywood runabout. Mixes up well and lays down smooooth. Sandable shortly after laydown without any pinholes commonly found in other fillers. Used the weight method for mixing ratio of smaller quantities with no problems. Haven't seen any problems to date.
Was this a gift?:
No
2/5/2013
4.0
A try it alternative
By Canoeboy1
from Elburn, IL.
About Me Casual/ Recreational
Pros
Easy to mix
Lower Price
Stays In Place
Cons
More Difficult To Fair
Best Uses
Comments about System Three QuikFair Fairing Compound:
I fill screw holes and small cracks or imperfections in wood plank on a boat. Goes on like peanut butter but is a bit more difficult to sand out fair than some of the other more expensive products.
Was this a gift?:
No
10/22/2012
5.0
Works well
By Mr.Wonderful
from Temperance, Mi
About Me Casual/ Recreational
Pros
Easy to Use
Cons
Best Uses
Fairing
Comments about System Three QuikFair Fairing Compound:
Easy to use.
Was this a gift?:
No
5/27/2011
(2 of 3 customers found this review helpful)
5.0
Great product...Easy to use.
By sailor3
from New York
About Me Advanced
Pros
Easy to Use
Protects Well
Cons
Best Uses
Comments about System Three QuikFair Fairing Compound:
I use it to fair the hull and keel of a sailboat.
Was this a gift?:
No
6/24/2010
(3 of 3 customers found this review helpful)
5.0
Very Versatile Product
By DIY Boater
from East Greenwich, RI
About Me Advanced
Pros
Easy to Use
Protects Well
Visually Pleasing
Cons
Best Uses
Indoor
Outdoor
Quick Fix
Wood Trim
Comments about System Three QuikFair Fairing Compound:
This is great stuff. I saw the demo at JD when it first came out and have been a fan ever since. It actually works as advertised. It mixes well, has a decent pot life, and the fumes are not noticeable. The consistency is between peanut butter and mayo, which means it can be used on vertical surfaces. 4 hour cure to sanding time is great. Used to fair and fill voids on Keel joint, hull surfaces, and finish off mounting holes in decks. Easy clean up from tools and extremities as well.
2/5/2010
(3 of 3 customers found this review helpful)
4.0
Thried three and liked this best
By chips and shavings
from Brookhaven, NY
About Me Professional
Pros
Easy to Use
Protects Well
Weather Proof
Cons
Best Uses
Best fairing compound
Comments about System Three QuikFair Fairing Compound:
It has a creamy consistency that spreads easily, dries in a short time and sands easily. Used for either wood or fiberglass fairing work, it is the best.
12/13/2008
(2 of 2 customers found this review helpful)
5.0
Uses limited to imagination
By Joe the welder
from South Mississippi
About Me Recreational
Pros
Easy to Use
Protects Well
Visually Pleasing
Weather Proof
Cons
Best Uses
Outdoor
Quick Fix
Wood Trim
Comments about System Three QuikFair Fairing Compound:
QF has many applications outside the marine enviro. I use it to top out #2 yellow pine fence boards prior to painting. I buy the cheapest, Quick Fair all blemishes and imperfections, sand it, paint it, the result is boards that look the equal to expensive C Grade, clear lumber @ half the price. It's easy and a lot of fun to use...
8/29/2008
(1 of 1 customers found this review helpful)
4.0
just nice and easy to work with
By dragonfly
from madison WI
About Me Beginner
Pros
Easy to Use
Cons
Best Uses
Comments about System Three QuikFair Fairing Compound:
easy to mix easy to level a surface easy to sand when dry
6/30/2008
(3 of 3 customers found this review helpful)
4.0
Quick Fair's great
By Choptank Boatworks
from Denton, MD
About Me Sponsored Professional
Pros
Consistent
Easy to Use
Cons
Best Uses
Comments about System Three QuikFair Fairing Compound:
Very fast to mix and to cure. Can get multiple coats on in one day. Easy to sand. Hides well under white top coats. Have had some paint curing problems when overcoating within 24 hours.
6/10/2008
(1 of 1 customers found this review helpful)
5.0
Awesome
By protek9543
from Lake Worth, Fl
About Me Recreational
Pros
Easy to Use
Protects Well
Visually Pleasing
Weather Proof
Cons
Best Uses
Fairing
Comments about System Three QuikFair Fairing Compound:
I like the fact it's epoxy, spreads like butter, and sands very easy.
Price Match Promise:
If you find a lower delivered price on a new identical item in stock and available for purchase from an authorized U.S. merchant.
- email us at pricematch@jamestowndistributors.com. This offer does not include special coupons or other promotional offers.
Special order items are not stocked and are ordered direct from the manufacturer. They are non-returnable, may take 2-4 weeks, price and shipping charges subject to change.
Checkout: 
Item(s) in your cart:
The item was added to your wishlist.
