Free shipping on orders over $99.99! Don't miss out!
$16.20 Limited Stock
Silicon Bronze Flat Washers
$16.20Limited Stock
Silicon Bronze Flat Washers
Ask a Question
5
Based on 1 Reviews
  • 5 Star

    100%

  • 4 Star

    0%

  • 3 Star

    0%

  • 2 Star

    0%

  • 1 Star

    0%

Silicon Bronze Flat Washers Customer Questions and Answers

7 of 7 Questions

Question

on the washer #6, can it be used on a 1/4" carage bolt?

Asked on 05/24/2012 by ben Molina

Top Answer

No it will not fit. Buy the 1/4 size

Answered on 05/25/2012 by BRUCE MITCHELL
See More Answers (4)

Answer

No, you need 1/4 washers unless you buy #6 and drill them out to 1/4"

Answered on 05/24/2012 by ERIC VAN DORMOLEN

Answer

Carriage bolts have a raised shoulder under the head, and require no washer on the head side. The flat washers I purchased is for 5/16 in. machine screws, and the washers thus have an inside daimeter of 5/16 in. and would be a bit large for the 1.4 in. bolt on the thread end, but could be used in some instances. I hope that answers your question. Alan

Answered on 05/24/2012 by ALAN MCWHIRTER

Answer

I bought this product to stay with the style of an antique commercial store front. There has been no problems since this product was installed and I found that the customer service with this company to be good. I have not needed anything from them since as I had found that there prices seemed to be more than the average cost from my normal suppliers.

Answered on 05/25/2012 by DAN EADIE

Answer

Ben The # 6 washer is too small for a 1/4" bolt. Also,most carriage bolts have a square flange near the head that is slightly larger than the diameter of the bolt itself. Try a larger size washer.

Answered on 05/29/2012 by JOHN ROTHAMEL
Answer Question

Question

What is the diameter of the hole in the #6 SB flat washer? Is it suitable to use as a burr on a 20d (6 ga. .203" dia.) copper nail?

Asked on 08/01/2018 by Bob from Salt Point, NY

Top Answer

3/8 and a smidge according to caliper

Answered on 08/01/2018 by joesailboat
See More Answers (2)

Answer

3/8 plus a smidge according to caliper

Answered on 08/01/2018 by joesailboat

Answer

This guide allows boatbuilders and woodworkers to match up the correct washer size with the fasteners they are using in terms of inner and out diameter. Size Thickness #6 9/64" 0.031" #8 11/64" 0.031" #10 3/16" 7/16" 0.037" #12 15/64" 0.040" 1/4 9/32" 0.050" 5/16 11/32" 0.050" 3/8 25/64" 0.050" 7/16 0.063" 1/2 9/16" 0.072" 5/8 11/16" 0.078" 3/4 13/16" 0.109" 7/8 15/16" 0.109"

Answered on 08/01/2018 by tjcuda
Answer Question

Question

Inside diameter on #12?

Asked on 11/25/2015 by Scott Sadil

Top Answer

For a 3/16" bold you need a #8 washer with a 3/16" ID for a tight fit.

Answered on 12/01/2015 by Rick White
See More Answers (2)

Answer

Okay -- so then what size would I need to clench my 3/16" copper drift bolts? That's what I'm looking for.

Answered on 11/25/2015 by Scott Sadil

Answer

1/4" ID, 9/16" OD

Answered on 11/25/2015 by Rick White
Answer Question

Question

What is the diameter of the hole and the overall diameter of the washer?

Asked on 02/17/2012 by Robert Funk

Top Answer

The flat washers have an inner hole diameter of 1/4" and the outside diameter of the washer is 11/16" Hope this helps.

Answered on 02/21/2012 by JOHN ROTHAMEL
See More Answers (1)

Answer

Well, here I am 10,000 miles away in Australia and I bought my silicon bronze flat washers three years ago but it seems I'm now the international expert on them. The ones I bought are called "1/4 inch". Their internal diameter is 0.254 inch and the external is 0.689 inch. We use metric here but to use fractions of an inch, the internal diameter is just over 1/4 inch and the external diameter is just over 11/16th. What else can I say about them? Umm..they're flat and...err...they're made out of silicon bronze. Regards, Steve

Answered on 02/18/2012 by STEVE TOWNSEND
Answer Question

Question

WHAT IS THE OD OF THE 3/4" ID BRONZE WASHER/

Asked on 04/30/2020 by JIM from MOUNT KISCO ,NY 10549

Top Answer

1-7/8"

Answered on 04/30/2020 by Paul
Answer Question

Question

Inside diameters of #10 and #8 silicon bronze washer?

Asked on 11/27/2015 by Scott Sadil

Top Answer

#10 id 7/32 od 1/2 thickness .049 #8 id 3/16 od 7/16 thickness .049

Answered on 11/30/2015 by Rick White
Answer Question

Question

What is the outside diameter (OD) of the #10 flat-washer?

Asked on 07/03/2013 by Brian P

Top Answer

I measured one at .435 in.

Answered on 07/03/2013 by Mark Dawber
Answer Question
1 of 1