This item is eligible for free shipping on orders over $99.99
This item will require additional time to ship
3M 4200 Fast Cure is a one-part general purpose polyurethane sealant with good adhesion to wood, fiberglass, gelcoat, plastic, and metal. When cured, 4200 forms watertight, weather-resistant seals on joints and boat hardware above or below the waterline.
4200 FC (fast cure) is ideal for hardware and bedding applications. It is paintable and sandable. While 3M 5200 sealant results in permanent bonds, 4200 has approximately half the strength, making it a good choice for applications where the bond may need to be broken in the future such as replacing hardware.
Size displayed is the 10 oz. cartridge. Choose Color and Cartridge Size.
October 8, 2021
This product worked well for my application, installing a centerboard gasket on my Mutineer dinghy. It was highly recommended as this gasket will need to be replaced sometime in the future as it will wear over time and use. 3M 4200 is a great product for adhesion especially for an item that may need to be removed at a later date.
April 28, 2020
use it for sealant on my boat
June 14, 2019
So far so good
July 20, 2016
this product was fresh
June 22, 2015
Great product. I replaced a drain fitting that was leaking into my boat. No more leak! Thanks JD
April 7, 2015
i use this 4200 for everything above the waterline,
October 27, 2014
First, Jamestown has the best prince! I used this to adhere aluminum skin to the side of wooden trailer and it worked perfectly. I have no complaints for its performance, what so ever. The only thing you need to what is that once you open, there is not a easy way to keep remainder from hardening. The best thing to do is to plan ahead and use full tube all at once. There are a few more things I need to mount, so I will be ordering soon.
March 5, 2014
These are great products and yes, if you allow it, they will get messy. When using these products: Choose the right product for the application! 5200 will yellow in the sun. Tape off area, give yourself room, make your lines straight. Put on gloves. Don't over fill, you will just have to wipe more off. Wipe the end of the tube with a paper towel when you pull it away Don't over tighten fasteners, you want to leave some adhesive between surfaces and finish tightening after cure. Wipe off excess, a little at a time to avoid smearing. Wipe down with Multi purpose cleaner or acetone for a clean smooth finish, remove tape after surface cures.
November 11, 2013
This product was easy to apply and dries very quickly. The only problem we had was the shipping.
June 17, 2013
I was using this product to bed and seal new jib tracks. When applying a 'dab', product was extremely stringy. Wind blown strands had to be cleaned off the hull and track. The air temperature was in the low 80's F. Also, the product appeared to set up much too quickly. I don't know if this was a defective batch since this was the first time I used this product.
Phasellus suscipit tincidunt tristique. Quisque mattis euismod ipsum, ac accumsan ante fermentum non. Vestibulum eget auctor lorem. Integer euismod justo nulla, nec ultricies ipsum pulvinar in. Duis sed fringilla turpis, at ultricies orci. Nam est turpis, consequat nec feugiat a.
Praesent sodales et ipsum
Mauris congue justo sit amet lacus sagittis, a tempor lectus tempus. Suspendisse quis nulla ac nibh accumsan tincidunt ac quis tortor. Proin dignissim aliquam odio, sed bibendum urna sagittis dapibus. Aenean ut tristique ante, sit amet ultrices nisi. Praesent eu dapibus augue. Mauris tempus suscipit ipsum, et malesuada tellus euismod eu. Quisque consequat turpis id feugiat lacinia. Vestibulum sit amet elementum augue. Quisque tempus ligula vitae placerat pulvinar. In egestas sodales lorem, id egestas lacus pharetra eget. Sed ac mi placerat, placerat nulla ut, imperdiet nunc. Mauris at felis vehicula, commodo est eu, ullamcorper purus.