This item is eligible for free shipping on orders over $99.99
A high density polyurethane foam roller, ideal for epoxy, paint and varnish applications. Can be cut into shorter widths to match the application area and cut into brushes for tipping off fresh coats of epoxy. Covers are 7-inches wide. Packages of two. Made by Arroworthy, professional grade brushing and roller products.
June 9, 2020
These rollers work excellent for epoxy paint or primer. Just keep in mind to keep you paint or primer fresh by mixing smaller quantities. These hold up well if you don't allow the epoxy paint or primer to start getting tacky, if it does it will pull the roller cover apart. Great item, I just painted my whole boat with just 2 of them. People will give roller covers a bad rap because of their mistakes, like mixing to much epoxy and allowing it to start getting sticky, will give them bad reviews. But if you use them correctly they hold up well.
January 23, 2020
The rollers come apart - delaminate - in less than 3 minutes of rolling epoxy. I have tried to send Jamestown photos, but have not yet found a way. This is not a product Jamestown wants to sell.
December 16, 2019
I was told these were the go to roller covers for epoxy. The worked fine for 10 minutes but then the foam starts to come loose.
August 8, 2018
Roller cover delaminated while using total boat epoxy primer
September 25, 2017
Friend was using one of my roller covers and it started to shed pieces of foam. A couple days later I was using one and it unrolled the foam from the base. When I peeled the foam off I found out that most of the surface was covered by very little or no glue - bad place to save money.
August 3, 2016
very poor quality. the foam is wrapped on like the cardboard roll of paper towels. bought 2 packs. out of the 4, only 1 had the edges of the foam close to each other, the others all had gaps of up to a 1/4".
April 15, 2013
These roller covers work great for epoxy. The thin polyurethane material doesn't introduce bubbles into the epoxy. I was able to use a single roller cover to epoxy-coat a 14.5 foot kayak hull.
April 11, 2011
I used these covers to apply epoxy primer to my boat's bottom. It's a fiberglass 27'. I could only get 1 coat on 1 side before the foam began to separate from the core. These covers did give nice, uniform coverage before the foam came loose. I purchased another package of covers from a different manufacturer and they worked much better.
November 16, 2010
Easy to cut these covers on band saw to fit other size rollers
September 23, 2009
Used to apply two-part epoxy primer and two-part polyurethane paint on aluminum mast, boom, spin pole. Foam covering separates from fiber core. To cover half the circumferance of my 66 foot mast would require 5 covers. Initially I cut the roller covers in half (3.5 inches) when rolling my boom. I thought this may have caused the problem. However, I got the same failure using a full size (uncut) roller cover on my mast. I switched to another brand of foam roller cover and was able to complete one full coat on my mast using only one roller cover. It's possible the curvature of the mast caused the foam covering to creep on the core and that this failure would not occur on large flat surfaces.
Phasellus suscipit tincidunt tristique. Quisque mattis euismod ipsum, ac accumsan ante fermentum non. Vestibulum eget auctor lorem. Integer euismod justo nulla, nec ultricies ipsum pulvinar in. Duis sed fringilla turpis, at ultricies orci. Nam est turpis, consequat nec feugiat a.
Praesent sodales et ipsum
Mauris congue justo sit amet lacus sagittis, a tempor lectus tempus. Suspendisse quis nulla ac nibh accumsan tincidunt ac quis tortor. Proin dignissim aliquam odio, sed bibendum urna sagittis dapibus. Aenean ut tristique ante, sit amet ultrices nisi. Praesent eu dapibus augue. Mauris tempus suscipit ipsum, et malesuada tellus euismod eu. Quisque consequat turpis id feugiat lacinia. Vestibulum sit amet elementum augue. Quisque tempus ligula vitae placerat pulvinar. In egestas sodales lorem, id egestas lacus pharetra eget. Sed ac mi placerat, placerat nulla ut, imperdiet nunc. Mauris at felis vehicula, commodo est eu, ullamcorper purus.