This item is eligible for free shipping
Fein Starlock Plus Teak Blades are the fastest, safest way to remove old caulking, adhesive or sealant from between your teak deck boards without damage to the wood.
The end of the blade is shaped to scoop out the old caulking, leaving enough room to re-apply new caulking.
To prevent damage to your decking, select a blade that is slightly smaller than the caulk line you want to remove.
Also works to remove caulking in difficult areas such as curves, cleats, and gunwales.
Sold one (1) blade per pack.
Starlock Plus blades and accessories fit OMTs with the Starlock Plus or Starlock Max mounting system directly, including most Fein and some Bosch OMTs; others will require an adapter. Check for compatibility with your OMT manufacturer.
Fein's 3D, snap-in Starlock mounting system is the new standard for Fein oscillating multi-tools. This innovative design allows Starlock accessories to be interlocked in three dimensions for better stability, increased efficiency, and greater safety.
Starlock accessories are available in standard Starlock, Starlock Plus, and Starlock Max versions designed for use with specific Fein multitool power ranges for greater longevity of the multitool itself.
Fein standard Starlock blades are compatible with a variety of OMTs; Starlock Plus blades and accessories fit Fein and some Bosch OMTs directly, others will require an adapter. Please refer to Using the Fein Starlock System for details, or check with your OMT manufacturer for compatibility.
Starlock Plus Teak Blades for Boat Deck Repair Fit:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
April 14, 2019
It requires a steady hand and good eye sight. It will cut the teak just as easy as the old grout.
January 20, 2019
The caulk channels in 1989 my boat are a 1/4" wide. I first tried a utility knife and scrapper. It took way too much time and energy. Then I tried a router. That was way too hard too control. So I bought the Fein 1/4" cutter and found it fit too tight in the channel as it would drift off and start cutting into the teak :-( So then I got the 3mm cutter. I go down one side then down the other side of the channel. Takes longer but is much easier to control. Also the bottom of the cutter has a rounded bottom so you will have to scrap the caulk out of the bottom corners with a caulk scraper.
January 2, 2016
Great blade. Stays sharp a very long time. Used it for teak seam caulk removal but also good for cutting coves lines in hull planking. Wish they also made a 60° "V" blade and a 2 mm blade.
June 9, 2015
Excellent Blade! I used it to remove the caulk from the entire deck on my 42' Grand Banks. Big Job and it held up. It works on different oscillating tools. Be sure to choose the correct blade width...too small and you will have to pass twice on groove to fully remove caulk.
May 18, 2010
Just purchased a 4mm blade and used it to remove seam compound on my 36' Grand Banks. It was easy to use, but as I was only repairing a few seams, making the joins to the existing seam compound was a bit tricky. Complete reseaming of the whole deck would be a long task.
Phasellus suscipit tincidunt tristique. Quisque mattis euismod ipsum, ac accumsan ante fermentum non. Vestibulum eget auctor lorem. Integer euismod justo nulla, nec ultricies ipsum pulvinar in. Duis sed fringilla turpis, at ultricies orci. Nam est turpis, consequat nec feugiat a.
Praesent sodales et ipsum
Mauris congue justo sit amet lacus sagittis, a tempor lectus tempus. Suspendisse quis nulla ac nibh accumsan tincidunt ac quis tortor. Proin dignissim aliquam odio, sed bibendum urna sagittis dapibus. Aenean ut tristique ante, sit amet ultrices nisi. Praesent eu dapibus augue. Mauris tempus suscipit ipsum, et malesuada tellus euismod eu. Quisque consequat turpis id feugiat lacinia. Vestibulum sit amet elementum augue. Quisque tempus ligula vitae placerat pulvinar. In egestas sodales lorem, id egestas lacus pharetra eget. Sed ac mi placerat, placerat nulla ut, imperdiet nunc. Mauris at felis vehicula, commodo est eu, ullamcorper purus.