Propspeed Foul Release Coating System Features

• Copper-free formula is safe for all underwater metals.
• Improves performance, speed, and fuel economy by preventing accumulation of marine growth.
• Contains no toxic biocides; safe for marine life.
• In drive, easily releases any fouling that may have accumulated on running gear while stationary.
• Eliminates cavitation and vibration, for a smooth, fast ride.
• Easy to apply.
• Multi-season coating prevents fouling and corrosion for up to 2 years.
• Available in DIY and Professional Kits.
• Kits include easy-to-follow instructions.
• Important! Install all zincs before applying Propspeed.

Propspeed Application: 5 Easy Steps

• 1. Prepare the metal surface: Sand to an 80-grit profile or use Propstrip (sold separately) to remove old coatings.
• 2. Initial cleaning: Use Propclean wipes to remove grease and other surface contaminants.
• 3. Metal conditioning: Apply Propprep solution liberally by rag or wipes, working over small areas at a time. Do not allow to dry out. Remove by wiping off thoroughly with a clean rag.
• 4. Apply Etching Primer (2 coats): Mix 2-part etching primer base and hardener in a 4:1 ratio. Apply 1st coat with a brush or foam roller.
• 5. Apply clear coat (1 coat): Apply Clear Coat topcoat by brush (do not use a foam roller) when the final coat of etching primer is dry to touch. This should be about at 80°F & 85% RH.

RPS200 - 200ml DIY Kit Contents

• (1) 96ml Etching Primer Base
• (1) 24ml Etching Primer Hardener
• (1) 80ml Clear Coat
• Propclean Wipe
• Propprep Wipe
• Mixing stick
• This kit will coat (1) 24'' prop. See Coverage Guide below for more coverage information.

RPS500 - 500ml DIY Kit Contents

• (1) 240ml Etching Primer Base
• (1) 60ml Etching Primer Hardener
• (1) 200ml Clear Coat
• Propclean Wipes
• Propprep Wipes
• Mixing stick
• This kit will coat (1) 36'' prop or a set of (2) 24'' props. See Coverage Guide below for more coverage information.

PSLKIT - 1L (1,000ml) Kit Contents - NOTE: Must purchase Propclean and Propprep separately

• (2) 240mL Etching Primer
• (2) 60mL Etching Primer Hardener
• (1) 400mL Clear Coat
• (2) mixing sticks
• IMPORTANT: Propclean Wipes & Propprep metal conditioner (wipes or liquid) are a required part of the Propprep system, and MUST BE PURCHASED separately with the 1L Kit.
• See Coverage Guide below for components that can be coated with the 1L Kit.

PRSCOMBO - Combo Pack - <b>Exclusive to Jamestown Distributors</b>

• (4) 1L Kits (782A)
• (1) pack of Propclean wipes (10/pk)
• (1) pack of Propprep wipes (10/pk)
• See Coverage Guide below for components that can be coated with the Combo Pack.

Additional Product Notes:

• If you run out of one item or another, Propclean, Propprep (available in a liquid form), Etching Primer, & Clear Coat are also sold separately.
• Propstrip, which can be used to remove old Propprep or other coatings, is sold separately.
• Also available are Propprep Paint Stirring Wheels (10/pk), which aid in the mixing of the 2-part Etching Primer and the Clear Coat.
• For protection on underwater lights and plastic bow thrusters, you can apply the Clear Coat directly (do not use the etching primer)

Top Tips for DIY Application - Planning and Preparation are the Keys to Success!

• Ensure that the surface is abraded to an 80-grit profile.
• Clean the surface thoroughly with the blue Propclean wipe.
• Remove the residue immediately with a clean, dry, white cotton rag. Repeat until there's no residue remaining.
• Condition the metal surfaces with the red Propprep wipe.
• Remove the residue immediately with a clean, dry, white cotton rag. Repeat until there's no residue remaining.
• Propprep is acidic—take extra care when wiping the surface.
• Apply the Etching Primer as soon as possible.
• Mix the Etching Primer Base thoroughly for about 2-3 minutes before adding the Etching Primer Hardener, or the system will not work properly.
• When the Base is stirred thoroughly, add the entire contents of the Hardener bottle into the Base container to ensure the proper 4:1 ratio. Mix thoroughly.
• Pour into a clean plastic paint tray.
• This system requires 2 coats of Etching Primer and 1 coat of Clear Coat. The timing of each coat is essential to enable proper chemical bonding between the coats.
• Apply the first coat of Etching Primer with a brush or roller.
• Wait approximately 3-5 minutes (at 80°F) to apply the next coat when the surface is dry to the touch (gloved fingertip touched to surface leaves an imprint but does not leave primer on glove).
• You have 3-5 minutes from applying the first coat of Etching Primer to applying the second coat.
• The same 3-5 minute recoat rule applies between the second coat of Etching Primer and the Clear Coat.
• For complete step-by-step details, read the Propspeed System Application Manual before applying Propspeed.

Additional Items Needed for Propspeed Application (sold separately)

• Dual action sander
• 80-grit sandpaper
• Plenty of clean cotton rags for wiping
• Plastic mixing containers
• Disposable brushes
• Disposable foam rollers
• Disposable plastic paint trays
• Mixing sticks
• Paper paint suits
• Disposable nitrile or latex gloves
• Eye protection
• Dust sanding mask