This item is eligible for free shipping
West System Six10 is a thickened epoxy adhesive that combines the strength and reliability of a two-part epoxy with the easy to use convenience of a single part formula.
Cartridges feature mixing tips that ensure the right ratio of resin and hardener is automatically mixed upon application. Easy to apply with a standard caulking gun, Six10's unique non sagging formula lets this epoxy bond tenaciously to wood, metals, fiberglass, and concrete. Colorless resin and hardener.
Are you working on your boat or project after work or on the weekend? Not having to mix resin and hardener beforehand saves time. Are you working overhead, on vertical surfaces, or tight spaces? This thick adhesive won't cause problems with sagging or runoff.
Additional static mixing tips can be purchased separately.
Six10 cures in temperatures as low as 50F. Working time is 42 minutes at 72F. It cures to a solid state in 5-6 hours and will take high loads in 24 hours. The cure time is faster at warm temperatures and slower in cool temperatures. The Six10 cartridge holds 190 ml of epoxy resin and hardener.
To use this adhesive, replace the retaining nut and plug on the West System Six10 dispensing cartridge with the 600 Static Mixer that comes attached to the cartridge. Dispense the mixed 2-part epoxy adhesive using a standard caulking gun.
The efficient internal geometry of the 600 Mixer thoroughly blends resin and hardener in a short mixing length for good application control and a minimum of waste. Place high-strength, non-sagging Six10 thickened epoxy exactly where it's needed in less time and with no mess.
Additional 600 Static Mixer nozzles are available in packages of two or twelve.
If you're doing a small job, you don't have to use the static mixer. Simply squeeze out what you'll need (maybe even a little less- you can always mix a little more if short) onto a piece of poster board or plywood and stir thoroughly. The resin and hardener are slightly different colors; use this color difference to gauge the thoroughness of your mix. All should be a consistent color with no streaks.
June 28, 2023
Used it to attach a fiberglass seacock backing plate to inside of hill. Makes the job easier.
February 27, 2023
Allows foe epoxy work overhead without dripping
September 9, 2022
I used this for a complex furniture glue up. I needed undersized floating tenons as I accidentally cut the mortises offset and didnt have the space/time to refill and cut them correctly. I used this for the tenons and pva for the rest of the joint(s). Worked PERFECTLY.
July 10, 2022
After sustaining F/G damage to my stern rail attachment bases from an impact at launch, it literally took just a few hours from start to finish to affect a structurally sound and cosmetically pleasing repair. Easy to use and strong as the original construction....maybe stronger.
June 8, 2022
I have a kicker motor attached to my transom for the last 11 years. It was installed by the dealer of the motor and the bracket. I noticed last year i had ants in my boat, only to discover that 2 of the mounting bolts through the transom , leaked. rotting the transom in that area. i removed the wood from the inside up to the fiberglass. replaced with marine plywood, epoxied to the fiberglass. i left a 1/8 to 1/4 border around the patch. Using Six 10 I was able to "calk" the border perimeter easily. it worked perfectly using a calk gun. Hardened better than new.
October 17, 2021
Building shelves in a hanging locker under the chart table . Used the West epoxy gel to help attach the wooden frame to each side where mechanical fasteners are very difficult to install given the 9.5" opening. The gel seemed into the gaps ultimately becoming hard as a rock securing both sides of the frame inside the locker.
February 19, 2021
Used the to fill an overhead gap that was very hard to reach. Filled the gap-no sag. Problem solved
December 8, 2020
My wife and I are rebuilding a 2000 motorhome with a lot of issues. This product works extremely well and is very easy to use. Thank you.
May 21, 2020
So glad to have come across this product!
April 23, 2020
I used this to fill some small to midsize gaps in an older boat. Worked great!!
Shipping information
Phasellus suscipit tincidunt tristique. Quisque mattis euismod ipsum, ac accumsan ante fermentum non. Vestibulum eget auctor lorem. Integer euismod justo nulla, nec ultricies ipsum pulvinar in. Duis sed fringilla turpis, at ultricies orci. Nam est turpis, consequat nec feugiat a.
Praesent sodales et ipsum
Mauris congue justo sit amet lacus sagittis, a tempor lectus tempus. Suspendisse quis nulla ac nibh accumsan tincidunt ac quis tortor. Proin dignissim aliquam odio, sed bibendum urna sagittis dapibus. Aenean ut tristique ante, sit amet ultrices nisi. Praesent eu dapibus augue. Mauris tempus suscipit ipsum, et malesuada tellus euismod eu. Quisque consequat turpis id feugiat lacinia. Vestibulum sit amet elementum augue. Quisque tempus ligula vitae placerat pulvinar. In egestas sodales lorem, id egestas lacus pharetra eget. Sed ac mi placerat, placerat nulla ut, imperdiet nunc. Mauris at felis vehicula, commodo est eu, ullamcorper purus.
By signing into your account, you represent that you have read and agree to our Terms and our Privacy Policy