Free shipping on orders over $99.99! Don't miss out!
Quantity
1 kt contains 1 kt

This item is eligible for free shipping on orders over $99.99
This item will require additional time to ship

Product Details

The Weld Mount Executive Fastener Kit offers a wide selection of hardware, parts and accessories. The 1001003 kit includes (1) tube of AT-8040 white acrylic adhesive and (10) AT-850 mixing tips. The 1001008 kit does not include adhesive. Both kits include several sizes of stainless panel studs, standoffs, footman's straps, small and large cable tie bases all packaged in a handy storage box.

The Weld Mount System features a unique line of fasteners designed to be adhesively bonded to almost any substrate. All Weld Mount fasteners are mounted with a unique non-sag acrylic adhesive which provides a permanent high strength bond.

Tech Specs
The AT-1001003 Kit Contains:
Part NumberDescriptionQuantity
AT-8040 50 ML White Acrylic Adhesive With 10 Minute Kick(1)
AT-300 Adhesive Dispensing Gun(1)
AT-850 Adhesive Mixing Tips(10)
AT-5 Large White Cable Tie Mount(100)
AT-3 Small White Cable Tie Mount(50)
AT-113 Large Footman's Strap(4)
PS62-832-16SS 1.00 in Long Panel Stud with #8-32 Threads(4)
ST125-1420-16SS 1.00 in Long Stud With 1/4-20 Threads 1.25 in Base(10)
ST125-1420-24SS 1.50 in Long Stud With 1/4-20 Threads 1.25 in Base(4)
ST125-1024-12SS .75 in Long Stud With #10-24 Threads 1.25 in Base(4)
ST125-1024-24SS 1.50 in Long Stud With 1/4-20 Threads 1.25 in Base(4)
Plano Storage Box with Movable Dividers see thru tote (1)
Step By Step Instructions
The AT-1001008 Kit Contains: All of the above - less Adhesive
Info & Guides

Description of the WELD MOUNT ADHESIVES

AT-1030 Is a specially formulated acrylic adhesive which cures in 12 minutes and has working strength within 40 minutes. AT-1030 is packaged in a 30 ML side by side dispenser cartridge with a built in plunger. Cut off the tips and dispense the amount needed for hand mixing. A cap is included to deal the cartridge for reuse. AT-1030 is a good general purpose bonder for all substrates except low energy plastics and rubber. AT-1030 has a shelf life of 12 months when stored at 72 degrees or less. The cartridge will bond 50-75 parts.


AT-2010 is also a two-part acrylic adhesive, which is formulated with high viscosity to allow instant bonding of Weld Mount System fasteners to any surface (horizontal, vertical or overhead). AT-2010 is packaged in a two part 50 ML cartridge which is mounted in the AT-300 adhesive dispensing gun using a 1 to 1 plunger. A special mixing tip is used to mix the two components thoroughly before use. AT-2010 sets in approximately 6 minutes, develops working strength in 15-20 minutes and dries to a light yellow color. AT-2010 is used typically for bonding Weld Mount parts in lighter duty applications.


AT-4020 acrylic adhesive will bond to fiberglass, steel, aluminum, glass, wood and many other substrates. However, it should be noted that AT-4020 adhesive will not bond well to StarBoard, low energy plastics or rubber. AT-4020 does not adhere as well to metals as it does to composite substrates. Weld Mount AT-4020 Acrylic Adhesive is a specially formulated to hold studs and standoffs without sagging. The Acrylic Adhesive cures in 10 minutes and has a working strength within 30 minutes at 72 Degrees F. The 50 ML cartridge will bond approximately 100-150 parts. AT-4020 is used primarily for bonding Weld Mount parts to composites in heavier duty applications.


AT-6030 adhesive is a two-component, 10:1 mix ratio structural adhesive with outstanding adhesion for bonding metals, carbon fiber, composites and most plastics. Most metals can be bonded without priming. This advanced product is designed to meet specific requirements of the transportation industry, including reduced read through on show surfaces. The combination of minimum surface preparation, primerless metal bonding and low read through makes AT-6030 ideal for a variety of assembly operations. AT-6030 is packaged in 40ML cartridges for use with our AT-300 dispensing gun and AT-650 mixing tips. AT-6030 is used typically for bonding Weld Mount parts in the heaviest duty applications.

Technical Information

Weld Mount System advantages:

  • Eliminate the need to drill in to a composite skin and exposing the core
  • Eliminate drilling, tapping, welding, grinding and finishing steps
  • Eliminate costly rework expenses caused by inadvertently drilling though substrates
  • Eliminate blocking added during lamination in order to have a place to put screws
  • Much stronger than traditional methods