This item is eligible for free shipping on orders over $99.99
Pink paint roller covers are suitable for applying fiberglass, epoxy, resins, industrial coatings, bottom paints and most marine finishes.
The Semi-Smooth 3/8" Nap is ideal for the application of thicker and heavier coatings where the final finish is not critical. The solvent resistant core is compatible with most finishes.
Medium rollers covers (with a 3/8" or 1/2" nap) are used for for sand-textured walls.
The Pink Roller Covers are available in 7 inch and 9 inch lengths.
May 16, 2021
Perfect size for doing Epoxy primer/barrier coat. Good price
October 27, 2020
Good size. Used a cut off roller holder in a drill to spin past a stiff plastic brush to rake the fuzz off the roller. Followed with packing tape to pull remaining loose strands. Got a nice finish on the bottom of my boat.
April 12, 2014
I have used the Redtree pink roller covers exclusively for over 30 years. They come in the 7 " size which works great for under 30ft power boats. Properly resduced paint applies evenly and the cover holds a good supply of paint. As for shedding, there is always some shedding whenever using new covers. As a professional painter, I always solvent wash the roller cover and spin it out. You can also gently brush out the cover with a wire bush to help remove loose fibers. I have used this to apply Interlux 2000E barrier coat and had no abnormal shedding problems. As for the other reviewer that did, I'm sure he did not wash, spin and prepare the cover prior to painting. Remember, this is an epoxy and solvent resistant cover. Don't compare it to a Purdy roller cover that you use in your home. If prepared for use, shedding is not a problem. Back rolling into a portion of the paint already setting up will pull fibers from the roller. So always roll away from a wet edge, move swiftly, and constantly add solvent to paint that is setting up too fast. And don't go back, even if you see a defect. Get it the next coat. Paint must be applied at the recommended coverage rate. That said, doing all this correctly in the sun, on a warm windy day, is essentially impossible. This is why big, professional marinas paint inside. No wind, no sun, no weather concerns. If painting outside, try to pick a cool, overcast, wind free day, around 50F - 60F. If impossible, then make sure you get 2 out of the 3. If not, it makes for a real challenge. For those that care, all roller fibers sand off easily after the paint has fully cured. If using ablative paint, a light hand sand before the next seasons launch will remove fibers and open the paint for the seasons use. Or just do what everyone else does, don't worry too much about it. It's bottom paint.
September 8, 2009
I used these roller covers to apply Interlux 2000E as a barrier coat. After a long summer of prepping the hull I was very discouraged with the amount of lint that was left behind with this roller cover. I tried a another cover for my second coat after carefully brushing it out to remove any loose fibers. There was still a lot of lint. I went to the local hardware store and purchased new covers and they did much better. After 3 additional coats of 2000E and 2 coats of anti-fouling I can still see the lint. Big bummer. I can't think of an application that would be suitable for these roller covers.
Phasellus suscipit tincidunt tristique. Quisque mattis euismod ipsum, ac accumsan ante fermentum non. Vestibulum eget auctor lorem. Integer euismod justo nulla, nec ultricies ipsum pulvinar in. Duis sed fringilla turpis, at ultricies orci. Nam est turpis, consequat nec feugiat a.
Praesent sodales et ipsum
Mauris congue justo sit amet lacus sagittis, a tempor lectus tempus. Suspendisse quis nulla ac nibh accumsan tincidunt ac quis tortor. Proin dignissim aliquam odio, sed bibendum urna sagittis dapibus. Aenean ut tristique ante, sit amet ultrices nisi. Praesent eu dapibus augue. Mauris tempus suscipit ipsum, et malesuada tellus euismod eu. Quisque consequat turpis id feugiat lacinia. Vestibulum sit amet elementum augue. Quisque tempus ligula vitae placerat pulvinar. In egestas sodales lorem, id egestas lacus pharetra eget. Sed ac mi placerat, placerat nulla ut, imperdiet nunc. Mauris at felis vehicula, commodo est eu, ullamcorper purus.