Free shipping on orders over $99.99! Don't miss out!

This item is eligible for free shipping on orders over $99.99

Product Details

AwlFair is a two-component premium trowelable filler for fairing, leveling, or smoothing surface imperfections due to gouges, pitting, dents, or weld seams. May be used above or below the waterline. This is the Base only. Awl-Fair Converter must be purchased separately.

*** FOR PROFESSIONAL USE ONLY ***

Info & Guides
Check the link for Awlfair Technical Data for most up-to-date and accurate manufacturer technical data.
Awlfair L.W. White Base (D8200)

Application Equipment- Trowels, Spatulas, longboard, or putty knives

Surface Preparation - Only apply over preoperly applied and prepared Awlgrip primers. 545 Epoxy primer, or High Build epoxy primers are best.

Mixing and Reduction - First shake or stir to a uniform consistency. Mix 1 part D8200 or D1019 with 1 part D7200 to a uniform pink color with no streaks or lumps in the mix. Do not add thinners or reducers to Awl-Fair products.

Application Instructions - Apply by trowel in thin layers to avoid air pockets to an area you can work in 15 to 20 minutes at 77 F/25 C, 50% RH when using D7200. When using D7200 Awl-Fair compound, work time is only 5 to 10 minutes at 77 F/25 C, 50% RH. Start application in low areas and build out into high areas. Allow to cure. Several applications may be required to fill large areas. Block sand with 30 to 60 grit and blow off sanding dust and residue before applying more Awl-Fair. Shape materials with tools of your choice.

Note: Awl-fair must be sealed with 545 Epoxy Primer. Filler primer, fairing materials, and sanding surfacers should be sealed with 545 Epoxy Primer before applying Awlgrip or Awlcraft 2000 Topcoats. This maximizes gloss and color hold-out in the topcoat.

Note: Avoid inserting air pockets when applying. Application of Awl-Fair in thin layers helps avoid air pockets. Remember to feather all edges and holes at 6 to 1 or 6 times the fill thickness for the feathered edge.

Warning: Do not incorporate into this Awlgrip coating system any thinner, additive, modifier, converter, or related product produced by any manufacturer other than Awlgrip. Do not apply to surfaces less than 3 C/5 F above the dew point, or to surfaces warmer than 41 C/105 F. Ambient temperature should be within 13 C/55 F - 40 C/104 F.

Technical Information

  • Type: Two Component Epoxy
  • Packaging: Available in 1 gallon and 1 quart containers
  • Theoretical Coverage: Sq. Feet/Gallon 1,604 Sq. Feet at one mil dry 6.8 Sq. Feet @ 240 mils (6,000 microns) DFT
  • Coverage calculations are based on theoretical transfer efficiency of 100%.
  • Actual coverage rate obtained will vary according to equipment choice, application techniques, part size and application environmen
  • Recoatability: AWL-Fair LW must be sanded before recoating. It must be overcoated with an epoxy primer such as 545 Epoxy Primer, HIGH BUILD, AWL-QUIK or ULTRA-BUILD before topcoating.
  • VOC: White Base D8200 - 0 g/lt or 0 lbs/gal. Fast Converter D7200 - 84 g/lt or .7 lbs/gal
  • Pot Life at 75 F/25 C, 50% RH = 1.5 to 2 hours.

Reviews for AwlFair LW Fairing Compound Base

3 of 3 Reviews

September 30, 2021

Based on exerience
By Frank from Rockland, Maine

Verified Purchase

AwlFair may be a little more expensive than the alternatives, and they might be as good, but I choose AwlFair because of how it worked in the past. In spring of 2015 I bought the quart-size (2 quarts) for a deck fairing project. It went fine - no pin holes, no sags on vertical surfaces, sands easily after overnight cure, and importantly no shrinkage (after months and years under an AwlGrip paint surface). I continued to use the same quart package for the next six years for odds-and-ends repairs. Performed exactly the same six years later when I finally scraped the bottom of the containers clean. Never clumped and never dried in the containers, in spite of the fact that the plastic cover don't seem to fit all that tight.

Bottom Line Yes, I would recommend to a friend

Was this review helpful to you?

July 19, 2020

Fairing compound
By Harebo from Atlanta

Verified Purchase

Used on 1970 Whaler. Easy to mix and use sands to a nice smooth finish

Ready for primer
Bottom Line Yes, I would recommend to a friend

Was this review helpful to you?

April 5, 2017

Works great!
By RKelly from Horsham, PA

Verified Purchase

Work's great! Arrived on time and does the job.

Bottom Line Yes, I would recommend to a friend

Was this review helpful to you?