COVID-19 Update: We are open & shipping orders! We are working hard to ship as quickly as possible, while ensuring the safety of our associates. Send us your questions and our Total Support Team will respond by email or phone as soon as we can!
Jamestown Distributors(800) 497-0010
Click to watch the JD Search Tutorial video & learn
all about searching and browsing on Jamestowndistributors.com
Ancor Stainless Steel Cushion Clamps are ideal for securing heavy wire bundles, cables, hose, pipe and tubing runs. 304 Stainless steel construction for maximum corrosion resistance.
(10) per box.
The item was added to your wishlist.
The item was added to your shop cart.
Prevents wear and corrosion
Ideal for harsh marine environments
Resistant to oils, acids, and salt water
Temperature range from -50 to +300 degrees F
Absorbs shock and vibration
Reduces unwanted noise
ABYC recommends: "Conductors shall be supported throughout their length or shall be secured at least every 18 inches (455 mm) by one of the following methods:" 220.127.116.11.10.
"By means of metal clamps lined with an insulating material resistant to the effects of oil, gasoline, and water." 18.104.22.168.10.3.
Cable Ties and Clamps
Is the cushion material in the stainless steel cushion clamps UV resistant? If not, what would you recommend to secure a wire bundle on top of a sailboat mast?
UV will deteriorate the gasket but it will take quite a while. Treating it with something like You could use split wire loom (https://www.jamestowndistributors.com/userportal/show_product.do?pid=4346) to protect the wires.
does the 3" mean it will go around three in. of of bundled hoses?
The stainless band by itself (without the rubber insulator) will be the exact measurement. With the rubber, I have found the diameter will be a little less (2 x the thickness of the rubber). If you hoses are exactly 3 inches, with no give, it may be too tight. However, considering rubber hoses have give, you will probably be OK. Otherwise, your option is to have about 1/16" gap at the clamp side.
That's a good question - if you mean the circumference (measurement around the outside of the bundled hoses) then I would think that is what they mean. I would doubt that it means a measurement across the center of that bundle (diameter) which at 3 inches would mean a much longer circumference and quite a large clamp.
I have never seen a 3". The 1" certainly can carry a bundle 1" in diameter. To support the load of a 3" one would need to use a bolt rather than a screw. A race might be more practical. The smaller sizes I have used work well.
JOHN A CALOGERO
need an assortment of 3/16, 1/4, and 5/16, do you have a box with 10 each?
DR RONALD E DICK
I hope they do-it's a great product for holding steering cables, wires, and the like. You'll have to ask JTD about the selection
what is the mounting hole size?
I didn't actually measure the hole because I didn't feel like taking the thing apart. But, I used an 11 mm SS fastener (nut and bolt) on it. So far the clamp has worked fine in our SE Alaska on my ocean going sailboat.
DR RONALD E DICK
The bottom strap is odd long for adjustment and the top hole is just under 1/4" . It'll take a # 8-#12 screw.
Excellent Product - Super Service
This is a wonderful product. It is well constructed and is ideal for mounting windshields to UTV roll cages. I can think of 1000 uses for these clamps.
Deep South, Alabama
The clamps hold a windshield for my Polaris Ranger
A high performance piece
Tie wraps and plastic clips and clamps work- but SS rubber lined clamps work better. High performance cars and boats use these clamps to anchor fuel lines, oil hoses, electric bundles etc. They give a professional look but more important they give professional results. Clamp it and forget it.