Perko edge mount oarlock sockets are available in natural finish zinc alloy or chrome plated with black plastic bearings. Screw size is #10. Sold by the pair.
Size: L 4" x W 7/8" x D 1-1/8"
The item was added to your wishlist.
The item was added to your shop cart.
Hole Inside Diameter
Oar Lock .5" shank and oarlock socket with .5" hole works ?????
Yes. 1/2 is a standard size. When product questions arise it is always handy to get the product model number from the JD listing and go to the manufacturer's website for better descriptions.
yes - it did for me
CHRISTOPHER W LONDON
Yes. Works great!
what is the thickness of the metal used to make these?
I would guess about 1/8 inch, trust me, they are sturdily built and will hold up, I installed two sets on a tandem rower and don't foresee any problems, good luckMike
I think at least 1/8 inch. Unfortunately I cannot measure them; they outlasted the boa.
I have an eight ft dinghy where should I mount the oar lock sockets?
when in the seated position, I would have them just toward you from about where your knees are.
I have 1/2" oar locks. Are the plastic sleeves 1/2 inch one of the responses says NO? Thanks Tom
I had to buy the same brand of oarlocks as the oarlock sleeves in order to get a decent working fit!
PETER VAN DINE
I have a set of these but haven't installed them yet. A brand new oarlock that measures (with a caliper) 0.495" is so tight it won't go in all the way. I'm not sure whether the sockets will "wear in" or if I'll have to ream out the sockets a little.
The oarlock sockets are not available to measure as the boat is stored out of town. I do have the oar locks that I use in them and they measure a scant 1/2 inch...that be about 1/64 or so smaller than 1/2inch....so I'd say that the sockets should probably work with 1/2 in oarlocks.
The inside diameter of the plastic sleeves is exactly 1/2 inch in diameter (measured with a micrometer). If your shanks are also exactly 1/2 inch in diameter the fit might be tight, but the 1/2 inch shanks on my oarlocks fit fine (just snug). The quality of the sockets is very good.Hope this helps!Bill R.
Perko edge mount oarlock sockets
Offset screw holes for mounting on the guwhale rail make these a good choice for small tenders.
Lunenburg Nova Scotia
works well with minor adjustment
I needed sockets for oarlocks with 1/2 inch shafts. After reading other reviews about the tight fit, I used a round file to file the interior nylon/plastic bushings until the oarlock shafts fit snugly. They worked well. I also mounted them on the outside of the top rail of my 18 foot Dory. There may be a good reason for mounting on the inside but with a 4 inch wide top rail, I would not have been able to touch the water with the oars with an inside mount. The outside mount also keeps me from banging the top rails with the oars.
Might work with a little adjusting.
I bought these awhile back but haven't installed them yet (mainly because of the fit). As another reviewer pointed out, they don't readily fit 1/2" oarlocks. I have a brand new set of oarlocks that measure .495" with a caliper and they are TIGHT. Really tight. I'm not sure if they will "wear in" or I'll need to ream the nylon bushings a little.
Good heavy duty Oarlock sockets
very happy with purchase [...]. thank you!
La Grande, Oregon
Did not fit my 1/2" oar post
These were suppose to be 1/2" oar locks, but my 1/2" posts did not fit into them. The plastic sleeve on the inside is too small to receive them. [...] Now I have [$] worth (2 pair) that I cannot use without some modification to ream out the plastic so the oar post fits in. Not happy with the product [...].
I ordered a set of this sockets after discarding an imported bronze set with holed that wasn't even machined and all misaligned.This Perko set is die cast so the precision is embed in the mold, the alignment of the holes perfect and the faces flat and square.The plastic bushing reduces the noise.