TotalBoat Outdrive AF 12 oz. Aerosol Spray for props drives  nd underwater metals
TotalBoat TotalBoat
  • TotalBoat Outdrive AF 12 oz. Aerosol Spray for props drives  nd underwater metals

TotalBoat Outdrive AF Barnacle Barrier Spray

TotalBoat Outdrive AF high-performance aerosol spray protects underwater metals on props, shafts, struts, trim tabs & thru hulls with a unique, copper-free formula that won't cause galvanic corrosion, and that will provide maximum corrosion protection. It dries to a hard, smooth finish that self-cleans while the boat is in service, with a high zinc content that serves as a dependable barnacle barrier for a full season.

Suitable for use in fresh or salt water. Apply to properly prepared metals, including bronze, brass, aluminum, stainless steel, cast iron, galvanized steel, and more. For use above and below the waterline. Available in a 12 oz. aerosol spray, in Matte Black.

NOTE: For maximum antifouling protection from hard and soft fouling on props and underwater metal parts, use TotalBoat Outdrive AF Antifouling Paint (sold in quart cans).

Matte Black  
IN STOCK - Available for pickup
Free shipping
$29.99 / ea
qty.   
$29.99
 The item was added to your wishlist.
 The item was added to your shop cart.
Tech Spec Product Info User Generated Content

TotalBoat Outdrive AF Aerosol Features

  • Inhibits corrosion on underwater metals.
  • Adheres strongly to properly prepared metals including bronze, brass, aluminum, stainless steel, cast iron, galvanized steel, and more.
  • Contains 4.00% zinc oxide to keep cured surface smooth in service.
  • Fast-drying formula.

 

Outdrive AF Aerosol (Primer: TotalBoat Aluminum Boat Barrier Coat)

SURFACE PREPARATION

General Prep: For use on all props and underwater metals (struts, trim tabs, shafts).TotalBoat Outdrive AF aerosol can be used over previous paint that is in good condition, or areas coated with TotalBoat TotalProtect Epoxy Barrier Coat Primer (or an appropriate metal tie-coat primer). Before application, clean the surface with a lint-free rag wetted with TotalBoat Dewaxer & Surface Prep. Spray multiple coats onto surfaces until the entire can is used. The effective life of the paint is proportional to the mil thickness of the paint applied.

Previously Painted Surfaces in Bad Condition: Strip back to the original substrate and prime with TotalBoat Aluminum Boat Barrier Coat, as directed. It's best to apply TotalBoat Outdrive AF Aerosol while the barrier coat is tacky, but no longer leaves a fingerprint. If this window is missed, let the barrier coat dry, sand lightly with 220-grit sandpaper, then apply Outdrive AF Aerosol.

Previously Painted Surfaces in Good Condition: Wipe the surface clean with TotalBoat Dewaxer & Surface Prep, allow to dry, and apply TotalBoat Outdrive AF Aerosol.

APPLICATION

Outdrive AF Aerosol is a high-solids paint that can settle to the bottom of the can. Failure to shake thoroughly before each use can result in clogging of the spray tip.

  1. Before use, shake can thoroughly after hearing the rattle; shake can occasionally during use.
  2. Spray surface with steady, even strokes at a distance of 8-10 inches.
  3. Clean out the tip, as directed, to prevent clogging
  4. Note: Apply at least 2 coats, allowing the surface to dry overnight between coats.

If Outdrive AF Aerosol is applied too thickly, it may require more time to dry before overcoating. Do not attempt to overcoat before previous coat has dried thoroughly. Allow to dry overnight before overcoating or launching. The effective life of the paint is proportional to the mil thickness of the paint applied. Use only when the ambient air, surface, and can temperatures are between 50°F and 90°F. For best results, allow to dry overnight, before launch. DO NOT PAINT ANY SACRIFICIAL ANODES OR ZINCS!

Substrates  Properly prepared metals for underwater use: Bronze, brass, aluminum, stainless steel, cast iron, galvanized steel, and previously painted surfaces 
Application Method  Aerosol spray. 
Application Temperature  Between 50 and 90°F 
Recommended Coats  Apply at least 2 thin coats (4 mils WFT); The more coats applied, the better the protection. 
Dry Time to Overcoat  Allow to dry overnight (50-90°F) 
Dry Time to Launch  Allow to dry overnight (50-90°F) 
Cleanup  TotalBoat Special Brushing Thinner 100 or TotalBoat Dewaxer & Surface Prep 
Thinning  N/A 
Surface Prep Dewaxer  TotalBoat Dewaxer & Surface Prep solvent wash 
Coverage  21 sq. ft. @ 2 mils dry film thickness (DFT) 
Primer  TotalBoat Aluminum Boat Barrier Coat 
Color  Black 
Finish  Matte 
WARNING: This product can expose you to chemicals including carbon black, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov

Below Water Line (yes/no): Yes
BRAND: TotalBoat
Type: Barnacle Barrier Paint
5.0 1

Best Outdrive Paint Ever

5

Outdrive remains fairly clean all season. Better than other brands I have tried.

Jack

Hingham Ma.

true

TotalBoat Outdrive AF Barnacle Barrier Spray

5.01

100.0

Related Items:
TotalBoat Blogs Live Tech Support Free Catalog