COVID-19 Update: We are open & shipping orders! We are working hard to ship as quickly as possible, while ensuring the safety of our associates. Send us your questions and our Total Support Team will respond by email or phone as soon as we can!
Jamestown Distributors(800) 497-0010
Click to watch the JD Search Tutorial video & learn
all about searching and browsing on Jamestowndistributors.com
Bronze body with monel basket design provide the ultimate corrosion resistance in Raw Water Strainers. Serviceable sea strainers protect the vital cooling system of your engine from clogging with marine debris. Solid bronze construction features NPT threaded ports.
Among the features of ARG series strainers are provisions on the strainer cap for the use of a spanner wrench to tighten or loosen the cap before or after maintenance.
Hand-tight is sufficient for a good seal for Groco strainers with threaded caps, but some boaters may prefer to snug the cover beyond hand-tight.
Cast bronze with 1/4 inch and 5/16 inch stainless steel pins. Opens to service deck plates or strainer caps with key holes up to 7 inches apart. Hangs conveniently near the strainer(s) location.
NPT (tapered) threads should be sealed with PTFE plumbing tape or equivalent.
The item was added to your wishlist.
The item was added to your shop cart.
Improved filter basket
Improved mount system
Monel Basket with .077 inch (2mm) holes
Improved design secures basket
No tie rods or gaskets
O-rings seal all mating surfaces
Easy service with screw-on cap
Mounting hardware is included
These general maintenance service kits help keep Groco ARG Series strainers in working condition. Each Kit contains a Cap O-ring, Sight Glass O-ring, Washer & Drain Wingnut Gasket
does the cap unscrew for easy winterizing?
Yes. Very easy.
Hello. ,yes it should unscrew relatively easily. If you find it is tite,when you put it back on wipe some silicone grease lightly around the rim.this should prevent it sticking next time.
you will need the groco tool to loosen the cap
I don't drain the filter for the winter. I draw my antifreeze through the strainer and into the engine exhaust cooling system using the engine pump. I have a valve that allows me to pull fluid from the normal cooling water or an open hose. The simple winterization is the main reason but in case there is hull damage and the bilge pumps wont handle it, I can also pump water out of the bilge through my two engines and overboard.
I am looking at instilling this inline filter to our system. The seawater pressure is 7 bar. Is this filter rated for this pressure?
This is a question that should be referred to the manufacturer. 1 Bar is one atmosphere of pressure so 7 bar is about 100 psi. I use my strainer in the cooling water flow for an 85 hp diesel engine. Contact Groco to determine safe use.
Where can I find a mounting bracket for this ARG-750 raw water strainer?
Thanks Nathan. After asking the question I found the brackets could be purchased separately.Really appreciate your help.Evelyn
The strainer comes with the mounting bracket, so you can get a brand new one with the bracket's included, or if you just want the brackets you will need the "GRO-ARG-505" upper bracket and the "GRO-ARG-504" lower bracket, both of which we can get for you and they're only $6.72 each, I also highly recommend getting a new mounting strap with that which is the "GRO-ARG-502" for only $3.36, thank you.
HI I have a 1982 bristol 41.1CC with Westerbeke 52. I would like to add a strainer, any rules of thumb as to size/capacity etc? Raw water hose is 3/4" , not sure why these boats did not come with raw water strainer.....thanksPeter HatchKennebunk ME
I just installed two new raw water strainers on my two perkins 4.236 diesels. I looked all over the place (Perkins shop manuals, etc) to determine how much water flow I needed without success. One of the best engine guys in town said that I could match the engine input water pipe (diameter) to the strainer input and output ports (dia). That would provide sufficient water flow even at extended RPM operation. You could go one diameter size larger on the strainers but the engine input line will cut the overall flow back to the max it can accept. We have tested both engines. The stbd engine just got a new manifold heat exchanger and the heat exchanger was professionally cleaned. No sign of overheating at extended run. The engine that has not yet had the heat fixed still runs within limits but is noticeably hotter that the stbd engine. So when you do the strainer upgrade, get your raw water exchanger system cleaned out at the same time for max performance.GoldenDogPrairie 36
I have Groco ARG raw water strainers on both my engine and utility sea water intakes. I have learned that the monel or plastic baskets are most suitable as the stainless basket will fail within a year in salt water. I would suggest the one inch strainer for your engine intake, to assure that grass etceteras will pass through the plumbing and in to the strainer without clogging elsewhere. My Groco ARG with monel basket, one inch size, engine raw water strainer was installed in 1984 and has about 4,000 engine hours on it with no problems. I would recommend a tee on the inlet with an engine zinc, whatever size your engine uses, to protect the bronze from corrosion.Fair Winds!Don, SV Southern Cross
The Groco unit is extremely well made. Heavy bronze casting and monel basket makes for a good performing unit.