Weld Mount Footmans Strap Mount
Weld Mount Weld Mount
  • Weld Mount Footmans Strap Mount
  • Weld Mount Installation
  • Weld Mount samples

Weld Mount Footman's Strap Mounts

The Weld Mount Footman's Strap Mounts are suitable for many marine and automotive applications. The Footman's Strap Mounts work well for battery tie downs, storage tank tie downs, the securing of heavy hoses or cables, or for deck and cabin mounted strap bases for securing portable equipment.

The Weld Mount Footman's Strap Mounts are designed to be bonded with the Weld Mount family of adhesives. The AT-113 is incredibly strong and is rated for over 300 lbs in tensile strength. The AT-113 strap mount is suited for rugged service, for example, it is currently bonded to the exterior of the Abrams A1 tank.

Available in white and black. The AT-113 strap mount can be painted to match other colors.

Sold in packs of (6), (25) and (100).

$19.93 / pk
 The item was added to your wishlist.
 The item was added to your shop cart.
Tech Spec Product Info User Generated Content

The Weld Mount Footman's Strap Mounts measure overall: 3-1/4 inches Long x 1 inch Wide and stand 5/8 inch Tall from the base.

The Footman's Strap Mounts will accept up to a 1.300 inch wide x 1/4 inch thick strap. The Footman Strap Mount is rated to handle over 600 lbs and is incredibly strong.

The Footman's Strap Mount may be painted to match any surface color.

The Weld Mount Footman's Strap Mounts are designed to be bonded with the entire family of Weld Mount Adhesives.

Description of the WELD MOUNT ADHESIVES

AT-1030 Is A specially formulated acrylic adhesive which cures in 12 minutes and has working strength within 40 minutes. AT-1030 is packaged in a 30 ML side by side dispenser cartridge with a built in plunger. Cut off the tips and dispense the amount needed for hand mixing. A cap is included to deal the cartridge for reuse. AT-1030 is a good general purpose bonder for all substrates except low energy plastics and rubber. AT-1030 has a shelf life of 12 months when stored at 72 degrees or less. The cartridge will bond 50-75 parts.

AT-2010 is also a two-part acrylic adhesive, which is formulated with high viscosity to allow instant bonding of Weld Mount System fasteners to any surface (horizontal, vertical or overhead). AT-2010 is packaged in a two part 50 ML cartridge which is mounted in the AT-300 adhesive dispensing gun using a 1 to 1 plunger. A special mixing tip is used to mix the two components thoroughly before use. AT-2010 sets in approximately 6 minutes, develops working strength in 15-20 minutes and dries to a light yellow color. AT-2010 is used typically for bonding Weld Mount parts in lighter duty applications.

AT-4020 acrylic adhesive will bond to fiberglass, steel, aluminum, glass, wood and many other substrates. However, it should be noted that AT-4020 adhesive will not bond well to StarBoard, low energy plastics or rubber. AT-4020 does not adhere as well to metals as it does to composite substrates. Weld Mount AT-4020 Acrylic Adhesive is a specially formulated to hold studs and standoffs without sagging. The Acrylic Adhesive cures in 10 minutes and has a working strength within 30 minutes at 72 Degrees F. The 50 ML cartridge will bond approximately 100-150 parts. AT-4020 is used primarily for bonding Weld Mount parts to composites in heavier duty applications.

AT-6030 adhesive is a two-component, 10:1 mix ratio structural adhesive with outstanding adhesion for bonding metals, carbon fiber, composites and most plastics. Most metals can be bonded without priming. This advanced product is designed to meet specific requirements of the transportation industry, including reduced read through on show surfaces. The combination of minimum surface preparation, primerless metal bonding and low read through makes AT-6030 ideal for a variety of assembly operations. AT-6030 is packaged in 40ML cartridges for use with our AT-300 dispensing gun and AT-650 mixing tips. AT-6030 is used typically for bonding Weld Mount parts in the heaviest duty applications.

Weld Mount System advantages:

  • Eliminate the need to drill in to a composite skin and exposing the core
  • Eliminate drilling, tapping, welding, grinding and finishing steps
  • Eliminate costly rework expenses caused by inadvertently drilling though substrates
  • Eliminate blocking added during lamination in order to have a place to put screws
  • Much stronger than traditional methods


BRAND: Weld Mount
Type: Footman Loop
5.0 3

Great Product


Great for straps. And didn't have to drill any holes in my boat!


Key largo, fl

Amazing Product!!!


I bought these to tie down my RTIC Cooler. I couldn't bring myself to pay $50 for the cooler tie-down kit with straps, and I also wanted to avoid putting holes in my new floor. I used Locktite Marine Epoxy to adhere and I am thoroughly impressed with the way everything turned out.




Better than pvc/patch D rings


Works great as battery and fuel tank anchors. Very stout. I wish they were U/V resistant, as my application is for an open 21 foot freighter canoe. I have painted them with "Epifanes matte wood finish", to that end.


Poconos PA


Weld Mount Footman's Strap Mounts



Related Items:
TotalBoat Blogs Live Tech Support