Todd Water or Holding Tanks, are made from one piece molded durable polyethylene to comply with FDA regulation CFR 177.1520 and meet Coast Guard standards. Tank openings are molded to eliminate stress cracking and leaking.
Appropriate for use as either water or waste holding, these tanks all have (2) 1-1/2" openings, and (2) 1/2" openings. All openings are female NPT (National Pipe Thread Tapered) and are located in the same relative position on one end of the tank. Plugs are supplied to configure for water or holding tank use.
Todd Fitting Relocation Kits are available to plug up existing threaded fitting openings and to custom position new fitting openings anywhere on the tank. Sold separately. Hose kits are also available separately.
The item was added to your wishlist.
The item was added to your shop cart.
Tank Part Number
Holding Tanks and Accessories
Does the 13 gal tank come with the fitting ready to clamp on a hose? Can the fitting be on top?
My tank came with threaded holes on one end of the tank. In, Out and Vent. You supply the fittings.As the pier turns and the anchor drags
No. The 13 gallon tank comes with plugs. You would have to add a suction rod to put the fittings on top.
Fittings do not come with the tank, but plugs come in the holes. Kits such as the one in the link below are very helpful in circumstances like yours to set it up with holes where you need them.https://www.jamestowndistributors.com/userportal/show_product.do?pid=51562&familyName=Todd+Water+Tank+Fitting+Relocation+Kit
JD Tech Associate
Yes to both.
I purchased the 6 gallon and it came with plugs for the holes but notfittings. Probably since hose sizes can vary so much. Simple pipe threadfittings found nothing special needed. My holes were on the sides.
Sorry no tank does not come with fitting for hose to clamp onto, they are all threaded holesall one one end of the tanl, so the second question would depend on what you consider to be the top of the tank
what are the dimensions of your 15 gallon tank?
25"L x 11"W x 16"H
What is the lead time on a custom tank? Would need two 15 gallon tanks with 1 1/4" fittings. One on each side of the tank.
Very good product ! Been using as water hold...,no problems of any kind
where does the vented loop go on the head instilation?
For a direct overboard discharge head or a mascerator pump out you need a vented loop.To a holding tank the head discharge runs directly into the tank.
Tank was delivered promptly and it included all fittings
Black water tank for my boat
Jamestown Distributors Rock!
I have ordered from Jamestown Distributors a lot and every item I've received is EXACTLY what I expected. Highly recommend!!
South Chicagoland, IL
Todd Water Holding Tank
Measures like they tell you. Strong tank with plenty of fittings to make it work. Replaced a very old potobale water tank on a sail boat. fit's well on the V berth area.
I have used Todd products before
I bought a Todd Captain's Chair for our Bridge many years ago and it has stood the time very well; so I think this Water Tank should stand the time as well. And that's why I chose it.
The TODD holding tank is the best, durable and easy to install. I realy recommend. Jamestown Distributors,[...]
Tank was an exact replacement
The dimensions were an exact replacement for my existing holding tank. However, the Todd unit is much stronger than the previous plastic holding tank. The installation was tight, but much less difficult than removing the old tank because the Todd tank openings are flush. I had to cut off the old fittings to get the old tank out.
Bill the boater
Deerfield Beach, FL
Todd tanks are good quality
I like the Todd tanks for upgrading old boat water systems. Original fiberglass tanks are very difficult to clean and make ok for drinking water. The Todd tanks do not make stored water taste funny. Easy to work with these tanks.