Moeller flanging tools let you custom shape your boat's drain tubes. Tools press the end cuts of brass or aluminum tubes to a perfect flange for drain tubes.
The resulting tubes will fit Snap-Tite, Turn-Tite and Trail Bail type plugs. Flange aluminum and brass tubes in one easy operation. Tools consist of a nut and bolt of hardened steel, steel fixture, and thrust ball bearings for smooth operation. Available in two diameters.
The item was added to your wishlist.
The item was added to your shop cart.
Drain Plugs and Tubes
The instruction sheet, included with this tool, reads that one of the flangers has a taper and the other doesn't. The tool I received has two straight flangers. Has the tool design been changed??
Its been a while since I used the tool but as I remember it one end was flat and the other was curved (flanged). Also in flanging brass tube its important to first anneal the end to be flanged so that it doesn't split.
Barry,If you look closely at the end of the tool you will see a very small flange. It appears to be flat but it truly is not. That very small flare on BOTH sides is what curls the flange tube.I and several other people have used this tool with fantastic results. Super pleased with this expensive tool.Remember to leave an 1/8 inch to 3/16 or so extra on the tube length before flanging it.Good luck
amazing results with Moeller products !
I bought 2 Moeller brass splash well tubes ( great quailty brass) to replace the original tubes on a 1995 Grady White Adventure and ordered the flanging tool to complete the flare during installation. I had also purchased 2 brass tubes from another marine store that were much thinner and noticeably lesser quality than the Moeller tubes.( sent them back for a refund) The installation was made simple with the flaring tool and it turned out perfect. Just take care to cut the tubes between 1/8"- 3/16" longer than thickness of the transom and follow the directions that come with the tool.
Chester County Pennslyvania
So easy to use
This was so easy to use and it made my work look professional. It was worth the money.
Great " little" tool
This flanging tool will work great for tubes less than 3 inches long, however if you expect to flange a 3 1/2 inch tube, you will have to visit a hardware store to purchase a longer bolt. This is not a big deal if you know ahead of time.
Hyde park NY
Good, bad and ugly
I bought your flange tool and drain tube installation kits (from this website) to install in my aluminum fishing boat.Someone around there or at the manufacturer needs to address a few issues with these products.I'm giving you the feedback in hopes of sparing other buyers the frustrations I experienced, as follows:1) The instructions show the bolt threaded all the way to the end. But what came in the package was a partially threaded carriage bolt. The threads stopped about an inch too short. I had to go to the hardware store and buy another bolt AND washers just in case the bolt snapped during installation and I had to use the carriage bolt provided. Given the high price of your product, that extra gas, time and expense was rather annoying.2) The instructions in your drain tube kit do not match the instructions in your flange tool kit. One says the O-ring goes on the inside; the other says it goes on the outside. It'd make more sense to have one on EACH side. But at the very least one would think the instructions would be the same since these things come from the same manufacturer.3) There were no recommendations as to what other sealant product to use to further secure and seal the connections. I used JB Weld. But if you know something else works better for these parts, one would think you'd give buyers a clue about that.My fishing buddy and I did finally get it to install once I bought the parts you failed to provide (and once I flipped a coin on which side deserved the one O-ring), I am happy with the result. But in my opinion it was far more frustrating than it should have been. And these fixes seem rather simple by the manufacturer. They might start by providing the correct bolt for the job and some unified instructions. The implication in your marketing suggests that the kit was complete, and it certainly was not.All in all, I'm pleased now that it's done. But I was not a happy camper yesterday about this.Finally, I strongly recommend future buyers installing in bare aluminum boats plan for this contingency; it's gonna be a drag if you don't. And I'd also urge you to go for the brass tube rather than the aluminum one. The aluminum one is flimsier than I'd prefer.
Lake Orion, Michigan
Quality tool. Professional finish.
Correct tool for proper installation of brass drain tubes on boats.
Only tool for the job!!
Quick and easy tool to use. Could'nt have done the job without it. Well worth the asking price.