Interlux Micron CF (Copper Free) Antifouling Bottom Paint Gallon
Interlux Interlux
  • Interlux Micron CF (Copper Free) Antifouling Bottom Paint Gallon
  • Interlux Micron CF (Copper Free) Antifouling Bottom Paint Quart
  • Interlux Micron CF Antifouling Bottom Paint Color Chart

Interlux Micron CF (Copper Free) Antifouling Bottom Paint

Micron CF is a superior multi-season, copper-free antifouling bottom paint. Micron CF features Biolux slime blocking technology with Econea adds protection against barnacles and zebra mussel growth.

Like all Micron paints, CF is an ablative or self-polishing coating that reduces paint build-up. Self-smoothing action helps reduce friction and improve fuel efficiency. High solids formula with reduced solvent emissions and VOC compliance.

Available in Black, Blue, Green, Red, and White.

Black  
IN STOCK - Available for pickup
$85.14 / qt
qty.   
$85.14
$78.99
$243.39
$243.39
$243.39
$243.39
$243.39
 The item was added to your wishlist.
 The item was added to your shop cart.
Tech Spec Product Info User Generated Content
APPLICATION AND USE:

Preparation:

Aluminum & Underwater Metals: Sandblast or sand with medium grade (grit) emery cloth to a bright metal finish and wipe clean. Apply one coat of Interprotect 2000E that has been thinned 15-20% with Reducing Solvent 2316N. Apply the Interprotect the same day as blasting or sanding. When the Interprotect 2000E is thumbprint tacky apply the first coat of Micron CF. Apply 2-3 coats of Micron CF following the proper dry times.

Factory Finished Aluminum: Prime with Primocon.

Bare Fiberglass: It is very important that bare fiberglass be properly prepared to completely remove the mold release wax. This will prevent delamination of the antifouling paint. Begin by scrubbing the surface thoroughly with a stiff brush using soap and water to remove loose dirt and contamination. Flush with fresh water to remove the soap residue and allow to dry. Remove mold release wax using one of the following Interlux products, Fiberglass Surface Prep YMA601 or Fiberglass Solvent Wash 202 following the product label instructions. To be certain the contamination has been removed, run water over the surface. If the water beads up or separates, repeat cleaning process. When the water sheets off, all contamination has been removed. After the surface has been properly cleaned, follow one of the application systems below.

No Sand System - Apply one thin, continuous coat of Interprotect 2000E or Fiberglass No-Sand Primer.

Sanding System - Sand with 80 grade (grit) paper. Remove sanding residue and wipe with Fiberglass Solvent Wash 202.

Bare Wood: Sand with 80 grade (grit) paper. Remove sanding residue. Apply first coat reduced 10% with Special Thinner 216. Fill seams, if necessary, with Seam Compound Brown 30.

Previously Painted Surfaces:

In Good Condition with Pacifica or Trilux 33: Sand with 80 grade (grit) paper. Remove sanding residue.

TBT Copolymers: If these coatings are more than a year old, wet sand the surface with 80 (grit) grade paper to a clean, firmly attached surface. Remove sanding residue. Apply 1-2 coats of TBT Sealer. Sand surface with 80 grade (grit) paper to a clean firmly attached surface. Remove sanding residue.

Non-TBT Copolymers: Apply 1 coat of Primocon.

Hard Antifoulings: Sand surface with 80 grade (grit) paper to a clean firmly attached surface. Remove sanding residue. Apply Micron CF.

In Poor Condition: Remove antifouling paint in poor condition with Interstrip Semi-Paste 299E. Sand and wipe clean with Fiberglass Solvent Wash 202.

Steel: Contact the Interlux Technical Service Department at 1-800-468-7589 for full information.

Hints:

Thinner: Special Thinner 216.

Thinning: Do not exceed 10% maximum.

Airless Spray: Pressure: 170-204 bar/2500-3000 psi; Tip Size: 0.53 mm/0.021"

Conventional Spray: Pressure: 3.44-4.47 bar/50-65 psi (gun pressure); 10-15 psi (pot pressure); Tip Size: 1.8-2.2 mm/0.071-0.087"

Other: To prevent premature failure, ensure correct amount of paint is applied using the coverage as a guide.

Some Important Points: Product temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Ambient temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Substrate temperature should be minimum 5°C/41°F and maximum 35°C/95°F. Do not use below 5°C/41°F.

Compatibility/Substrates: Apply to clean, dry, properly prepared surfaces only. Surface must be dry and clean, and free from grease, loose paint etc. Do not apply Micron CF directly to aluminum. All metal surfaces must be primed with Interprotect 2000E/2001E or Primocon. Do not apply direct to tin-based paint such as Micron 33, Micron 44 or Tri-Lux IIT.

Number of Coats: 2 coats, 3 on bare wood (first coat thinned)

Coverage: (Theoretical) - 518 ft²/gal

Recommended DFT: 2 mils dry

Recommended WFT: 3 mils wet

Application Methods: Airless Spray, Brush, Conventional Spray, Roller. DO NOT SPRAY without following proper safety procedures for spray application. Go to www.yachtpaint.com for spray information.

TRANSPORTATION, STORAGE & SAFETY INFORMATION:

Storage: Exposure to air and extremes of temperature should be avoided. For the full shelf life of this product to be realized ensure that between use the container is firmly closed and the temperature is between 5°C/41°F and 35°C/95°F. Keep out of direct sunlight.

Transportation: Micron CF should be kept in securely closed containers during transport and storage.

Disposal: Container Disposal: Triple Rinse (or equivalent). Then offer for recycling or reconditioning, or puncture and dispose of in a sanitary landfill or by other procedures approved by state or local authorities. Pesticide Disposal: Open dumping is prohibited. Pesticide, spray mixture or rinsate that cannot be used or chemically reprocessed should be disposed of according to procedures approved by Federal, state, or local disposal authorities.

General: Read the label safety section for Health and Safety Information, also available from our Technical Help Line. Contains biocides. Spraying of antifouling paints is prohibited in Canada.

Technical Specifications:

  • Finish: Low Gloss
  • Specific Gravity: 1.72
  • Volume Solids: 66%
  • Typical Shelf Life: 2 years
  • VOC (As Supplies): 330 g/lt
  • Unit Size: 1 US Quart, 1 US Gallon
  • Number of Coats: 2 minimum, 3 coats for bare wood (first thinned)
  • Coverage: (Theoretical) - 518 ft²/gal

 

Drying Information  50 Degrees F  73 Degrees F  95 Degrees F 
Touch Dry (ISO)  3 hours  2 hours  1 hour 
Immersion  9 hours  6 hours  4 hours 
Overcoating Substrate Temp  50 Degrees F  73 Degrees F  95 Degrees F 
  Minimum - Maximum  Minimum - Maximum  Minimum - Maximum 
Micron CF  6 hours - ext  4 hours - ext  2 hours - ext 
BRAND: Interlux
Type: Copper Free AF Paint
Related Items:
TotalBoat Blogs Live Tech Support