Fiberglass Cloth - Triaxial Weave
Vectorply Vectorply Logo
  • Fiberglass Cloth - Triaxial Weave
  • Vectorply E-TLX 2200-10
  • Triaxial Weave Fiberglass Cloth

Fiberglass Cloth - Triaxial

This triaxial fiberglass cloth is an E-TLX 2200-10 (0, +/-45°) 23.55oz/sq.yd E-Glass made by Vectorply. Triaxial fiberglass combines the benefits of unidirectional and standard +/-45 biaxial fiberglass. The fiber tows run in perpendicular angles to add strength and reduce both torsional and longitudinal flexion and strain. The weave is retained by a thin polyester stitching which holds the tows in place without affecting structural integrity.

Triaxial Fiberglass impregnates easily and is ideal for large glassing jobs focusing on strengthening a surface while adding minimal weight. Experience excellent results when used during wet lay-up, vacuum bagging, or infusion molding.

This cloth is sold by the yard or roll (106 yds) and is 50" wide.

IN STOCK - Available for pickup
$15.68 / yd
 The item was added to your wishlist.
 The item was added to your shop cart.
Tech Spec Product Info User Generated Content
*Please specify if continuous lengths are required. This is usually the standard for all of our composites, however when reaching the end of a roll, orders may be completed in multiple lengths to total the ordered quantity.
Ultimate Stress  E-TLX 2200 Resin Infused  E-TLX 2200 Open Mold 
Longitudinal Tensile  73.0 KSI  53.0 KSI 
Longitudinal Compression  73.0 KSI  53.0 KSI 
Transverse Tensile  19.0 KSI  14.0 KSI 
Transverse Compression  19.0 KSI  14.0 KSI 
In-Plane Shear  29.0 KSI  21.0 KSI 
Longitudinal Flexion  92.0 KSI  67.0 KSI 
Transverse Flexion  19.0 KSI  14.0 KSI 


  • Resin infused laminate made with vinyl ester resin 200 cps viscosity @ 77 degrees F
  • Open mold laminate made with polyester resin
  • All Standard reinforcements should be infused with a flow aid or Vectorfusion reinforcements.


BRAND: Vectorply
Weave: Triaxial
5.0 4

Thick and strong. Take your time.


Very strong and thick fiberglass. Only needed one layer. Was a little difficult to work with because of its thickness. However, I am confident in its strength. After initial laying, there is a deep woven pattern that fills easily with filler and thickener. This fabric was applied to 1/4 inch (old) plywood hull with multiple repairs. A thinner glass fabric would be adequate for other applications, but I like how this turned out with only one layer on this refurbish job. I used a lot of epoxy. JD has been uniformly excellent for mail order.




Worked great!


Replace transom on 1985 smokercraft boat,had to fill 3/8 inch gap in hull, took 8 layers of 24 oz. fiberglass,1 1/2 gal. Of 105 epoxy. Worked great! Would not buy products any where else. You're staff was friendly and helpful!


South central IN. Lake Monroe


super strong


i used this to install a transom on a Mirage River racer tunnel boat. we have literally beat this boat to death in rough water and have not seen any stress or cracking since the repair. I will defiantly be using this again when I install stringers and transom on my Hydrostream Vector.

mike m



Great product great price


For the price this is an amazing product. I used it for building skis and it was easy to work with and very stiff when cured. I also loved how wide it came, and how few meters I needed to order to get the amount I needed.

Pablo the goat

Boulder, CO


Fiberglass Cloth - Triaxial



Related Items:
TotalBoat Blogs Live Tech Support