Free shipping on orders over $99.99! Don't miss out!
$159.87 In Stock
Windline Over-Platform Drop Ladder
$159.87In Stock
Windline Over-Platform Drop Ladder
Ask a Question
4.6
Based on 9 Reviews
  • 5 Star

    56%

  • 4 Star

    44%

  • 3 Star

    0%

  • 2 Star

    0%

  • 1 Star

    0%

Windline Over-Platform Drop Ladder Customer Questions and Answers

7 of 7 Questions

Question

I have a 2001 SeaRay 180 bow Rider. In the 2001 180 BR Parts Manual the ladder is listed as 1256155 ladder swim ss 3 step telescop. Also they list 1342138 cap, ladder end top for # 1085166/236+266 and 1342146 cap, ladder end BTM for 1085166/1256155. I need the complete hardware from the rear deck of the boat. Will this ladder fits my boat before I purchase?

Asked on 04/02/2014 by Douglas Jayne

Top Answer

Thank you, The swim platform is 13 1/2 inches wide so I might have a problem. I did measure the distance to the water and that should be no problem. The old ladder was 11 1/2 inches wide and the new one is 12 inches. I will have to drill new holes and fill in the old holes. Thanks again Doug

Answered on 04/03/2014 by Douglas Jayne
See More Answers (4)

Answer

Ok thanks. I will give it a try

Answered on 04/02/2014 by Douglas Jayne

Answer

don't know, mine is on a 25' grady 1988 and works fine

Answered on 04/02/2014 by LARRY BARR

Answer

Does the ladder mount on a swim platform? If so, provided that your swim platform is at least 15 inches deep, this ladder will fit. However, it probably won't be an exact match for the ladder that originally came with the boat. If that is the case, you will have to drill new holes in the platform mount the ladder. That shouldn't be too hard to do. If the ladder actually mounts to the rear deck of your boat, though, the same problem exists: new holes are likely to be required. Also, the ladder might not be long enough to go deep enough into the water to be useful.

Answered on 04/03/2014 by WALTER PATSTONE

Answer

My swim platform is flat so the brackets lay flat. The holes from the old 2 step ladder didn't line up so we had to drill 3 new holes (we used 1 of the old holes)then filled the others with sealant. I like the ladder but I wish it was about 3 or 4 inches wider.

Answered on 04/02/2014 by JEFF SIMARSKI
Answer Question

Question

I would like to purchase this ladder. However, it would be helpful to know the mounting bracket dimensions. My present ladder support bracket holes are spaced 13" +/- inches apart (rung to rung) and and 2 1/2" spaced on each side?

Asked on 06/14/2012 by steve brown

Top Answer

The three step ladder I purchased had a spread of 10.13" centerline to centerline on the holes in the mounting brackets. Seems like the spacing on the 4 step ladder was a little more, but not 13". The spacing of the holes on either side are less than 2 1/2". If you check the Windline site, I believe they give at least the side to side dimensions on all their ladders. Good Luck.

Answered on 07/09/2012 by JIM NEAL
See More Answers (2)

Answer

Love to help but the ladder is in Mx. HAve not used the ladder as we went a different direction with a larger dive ladder. Ron

Answered on 06/14/2012 by RON RUNION

Answer

Steve off the top of my head that's about right--but I'd have to go measure it. It may be that your existing holes are just close enough to what's needed for this ladder that they should be filled and new holes drilled. There is a little play in the brackets side to side because they attach to the ladder with just one bolt. I'll measure and send you the actual dimensions.

Answered on 07/31/2012 by LANCE RYDBERG
Answer Question

Question

I have a 1999 stingray with existing winlline 2 step over the platform telescopic ladder would like to leave th existing hardware and bracket on the platform since back up plates are internal factory installed and just swap out the steps at the swivel point The issue is existing 2 step is 12" on center at the swivel and not sure if the would match a newer 3 step Thanks

Asked on 03/26/2021 by Robert from undisclosed

Top Answer

Contact the manufacturer at www.lobostar.com

Answered on 04/03/2021 by Paul
Answer Question

Question

I have 2 step windland over the platform swim ladder and really in need to 3 step Can I simply use the existing 2 step attached mounting plates and simple swap out the steps where they are connected at the attachement hardware at the swivel point

Asked on 05/16/2020 by Bobby from Clear Spring Maryland

Top Answer

Yes.

Answered on 06/02/2020 by Paul
Answer Question

Question

I'm looking to purchase a ladder to replace the one on my 27' Tiara. The existing ladder holes are 11" apart (on center) and each side of the existing bracket has 2 holes which are 2" apart on center also. Can you tell me if the 3 step ladder ( which is spec'd at 12" wide) has the same hole pattern as my old one? I prefer to not have to drill new holes, thank you.

Asked on 08/08/2017 by Pete from Macomb, Mi.

Top Answer

I don't see the hole centers specified on the Windline ladder. Here is there number: 310-516-9812

Answered on 12/06/2017 by JD Tech Team
Answer Question

Question

I have two of your ladders. The fold down telescopic one. The black plugs at the end have fallen out of both. Can these be purchased.

Asked on 03/26/2017 by Mike from Naples Florida

Top Answer

Sorry not available.

Answered on 03/28/2017 by JD Tech Team
Answer Question

Question

what are the demensions of three step ladder?

Asked on 02/04/2012 by Undisclosed

Top Answer

I haven't used it yet since I installed on boat. I wish it was a little wider since the 2 step I replaced was wider. I don't know dimensions but I assume it's what is stated in the catalog.

Answered on 02/06/2012 by ROBERT LEBEL
Answer Question
1 of 1